78253 Series
MAX253 Compatible Converter Transformers
TYPICAL CHARACTERISTICS (VOLTAGE CURVES) continued
VOLTAGE DEVIATION
78253/55(M)C
78253/35(M)C
110
105
110
105
100
95
100
95
90
90
100
50
-50 -25
0
75
100
25
50
-50 -25
0
75
25
Temperature (°C)
Temperature (°C)
78253/35(M)VC
78253/55(M)VC
110
110
105
105
100
95
100
95
90
90
100
50
Temperature (°C)
-50 -25
0
75
25
25
Temperature (°C)
100
50
-50 -25
0
75
SOLDERING INFORMATION1
Pin finish
TECHNICAL NOTES
ISOLATION VOLTAGE
Matte tin
REPEATED HIGH-VOLTAGE
ISOLATION TESTING
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Volt-
age’, ‘Proof Voltage’, ‘Dielectric Withstand
Voltage’ & ‘Isolation Test Voltage’ are all terms
that relate to the same thing, a test voltage,
applied for a specified time, across a compo-
nent designed to provide electrical isolation, to
verify the integrity of that isolation.
300˚C for 10 seconds
220˚C2
Peak wave solder temperature
Peak reflow temperature
It is well known that repeated high-voltage
isolation testing of a barrier component can
actually degrade isolation capability, to a
lesser or greater degree depending on ma-
terials, construction and environment. This
series has toroidal isolation transformers,
with no additional insulation between pri-
mary and secondary windings of enameled
wire. While parts can be expected to with-
stand several times the stated test voltage,
the isolation capability does depend on the
wire insulation. Any material, including this
enamel (typically polyurethane) is suscep-
tible to eventual chemical degradation when
subject to very high applied voltages thus
implying that the number of tests should be
strictly limited. We therefore strongly advise
against repeated high voltage isolation test-
ing, but if it is absolutely required, that the
voltage be reduced by 20% from specified
test voltage.
TUBE OUTLINE DIMENSIONS
0.43
(10.95)
All products in this series are 100% production
tested at their stated isolation voltage.
0.16 (4.00)
A question commonly asked is, “What is the
continuous voltage that can be applied across
the part in normal operation?”
0.023 0.005
(0.60 0.15)
0.51
(12.95)
For a part holding no specific agency approv-
als both input and output should normally be
maintained within SELV limits i.e. less than
42.4V peak, or 60VDC. The isolation test
voltage represents a measure of immunity to
transient voltages and the part should never
be used as an element of a safety isolation
system. The part could be expected to function
correctly with several hundred volts offset
applied continuously across the isolation bar-
rier; but then the circuitry on both sides of the
barrier must be regarded as operating at an
unsafe voltage and further isolation/insulation
systems must form a barrier between these
circuits and any user-accessible circuitry ac-
cording to safety standard requirements.
0.22 (5.50)
0.15
(3.80)
0.62 (15.70)
Tube length: 18.3 0.08 (465 2). Tube quantity: 50.
Tube material: Antistatic coated clear pvc.
Unless otherwise stated all dimensions in inches(mm) 0.01 (0.25).
This consideration equally applies to agency
recognized parts rated for better than
functional isolation where the wire enamel
insulation is always supplemented by a
further insulation system of physical spacing
or barriers.
All specifications typical at TA=25°C
For further information, please visit www.murata-ps.com/rohs
For high temperature reflow parts see 78253J series.
1
2
www.murata-ps.com/support
KMP_78253C_D04 Page 4 of 5
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
