STK14C88C
Package power dissipation capability
(TA = 25 °C) ................................................................. 1.0 W
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Surface mount Pb soldering temperature
(3 seconds) .............................................................. +260 C
Storage temperature ................................ –65 C to +150 C
Maximum accumulated storage time:
DC output current
(1 output at a time, 1 s duration) ................................. 15 mA
Static discharge voltage
(per MIL-STD-883, Method 3015) ......................... > 2001 V
At 150 C ambient temperature ...................... 1000 h
At 85 C ambient temperature .................... 20 Years
Maximum junction temperature ................................. 150 C
Supply voltage on VCC relative to VSS ...........–0.5 V to 7.0 V
Latch-up current ....................................................> 140 mA
Operating Range
Voltage applied to outputs
in high Z state ..................................... –0.5 V to VCC + 0.5 V
Range
Industrial
Military
Ambient Temperature
–40 C to +85 C
VCC
4.5 V to 5.5 V
4.5 V to 5.5 V
Input voltage .......................................–0.5 V to VCC + 0.5 V
–55 C to +125 C
Transient voltage (< 20 ns)
on any pin to ground potential ............–2.0 V to VCC + 2.0 V
DC Electrical Characteristics
Over the Operating Range
Parameter
VCC
Description
Power supply
Test Conditions
Min
4.5
–
Typ [3]
Max
5.5
70
Unit
V
5.0
–
ICC1
Average VCC current
tRC = 35 ns
Industrial
Military
mA
mA
Values obtained without
output loads (IOUT = 0 mA)
–
–
85
ICC2
Average VCC current during
STORE
All inputs don’t care,
Industrial
Military
–
–
–
–
10
15
mA
mA
VCC = Max
Average current for duration
tSTORE
ICC3
Average VCC current at
All inputs cycling at CMOS levels.
Values obtained without output loads
(IOUT = 0 mA).
–
35
–
mA
t
RC = 200 ns, VCC(Typ), 25 °C
ICC4
Average VCAP current during
AutoStore cycle
All inputs don’t care. Average Industrial
–
–
–
–
–
–
–
–
5
10
5
mA
mA
mA
mA
current for duration tSTORE
Military
ISB
VCC standby current
CE > (VCC – 0.2 V).
Industrial
Military
VIN < 0.2 V or > (VCC – 0.2 V).
Standby current level after
nonvolatile cycle is complete.
Inputs are static. f = 0 MHz.
10
[4]
IIX
Input leakage current
(except HSB)
VCC = Max, VSS < VIN < VCC Industrial
–1
–5
–
–
–
–
–
–
+1
+5
+1
+5
+1
+5
A
A
A
A
A
A
Military
Industrial
Military
Input leakage current (for HSB)
–100
–100
–1
IOZ
Off-state output leakage current VCC = Max,
SS < VOUT < VCC
CE or OE > VIH or WE < VIL
Industrial
Military
V
,
–5
Notes
3. Typical values are at 25 °C, V = V
. Not 100% tested.
CC
CC(Typ)
4. The HSB pin has I
= –2 µA for V of 2.4 V when both active high and low drivers are disabled. When they are enabled standard V and V are valid. This
OUT
O
H
O
H
O
L
parameter is characterized but not tested.
Document Number: 002-23965 Rev. *A
Page 7 of 21
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
