Single Deck Rotary Switches
CIRCUIT DIAGRAMS AND REAR VIEWS: PC Mountable AND Solder Lug Terminals
Circuit as Viewed From Shaft End
Rear View
.366 ± .015
.366 ± .015
(9,30 ± 0,38)
DIA. CIRCLE
OF CENTERS
(9,30 ± 0,38)
DIA. CIRCLE
OF CENTERS
9
10
8
5
11
12
7
6
30° Angle
.190 ± .015 (4,83 ± 0,38)
DIA. CIRCLE OF CENTERS
(PC MOUNT AND
.190 ± .015 (4,83 ± 0,38)
DIA. CIRCLE OF CENTERS
(PC MOUNT AND
1
of Throw
15°
15°
2
POS. 1
POS. 1
3
4
SOLDER LUG)
SOLDER LUG)
30° TYP.
30° TYP.
ONE POLE
COMMON LOCATION
FOR 2 POLE SWITCH
9
10
9
10
8
5
11
8
11
12
C3
C2
7
7
12
1
C4
COMMON LOCATION
FOR 1 POLE SWITCH
C2
C1
1
C1
6
6
2
2
5
4
3
4
3
FOUR POLES
TWO POLES
.340 ± .015
(8,64 ± 0,38) DIA.
CIRCLE OF CENTERS
8
8
9
9
7
7
10
C2
10
1
6
6
36° Angle
of Throw
DIMENSION A
DIA. CIRCLE OF CENTERS
C1
1
18°
5
5
POS. 1
4
2
4
2
36° TYP.
3
3
COMMON LOCATION
FOR 2 POLE SWITCH
PC Mount
Terminals
Solder Lug
Terminals
TWO POLES
ONE POLE
Dimension
A
.184 ± .015
(4,67 ± 0,38) (3,20 ± 0,38)
.126 ± .015
COMMON LOCATION
FOR 1 POLE SWITCH
SPECIFICATIONS
Electrical Ratings
Materials and Finishes
critical than those listed; longer operation is
required; a larger make and break current is
required; the operating environment includes
elevated temperatures or reduced pressures.
Contact Carry Rating: Switch will carry 6
amperes continuously with a maximum
contact temperature rise of 20°C.
Housing:Zincdiecast,zinc-platedwithchromate
treatment.
MountingNut:Brass,zinc-platedwithchromate
treatment.
Lockwasher: Spring steel, zinc-plated with
chromate treatment.
Panel Seal: Silicone rubber
Shaft and Stop Arm: Zinc die cast, zinc-plated
with chromate treatment.
Retaining Ring: 302 Stainless steel, passivated
Shaft Seal: Silicone rubber
Stop Pins: 303 Stainless steel, passivated
Detent Rotor: Molded thermoplastic
Detent Spring: Tinned music wire
Detent Balls: Steel, nickel-plated
Contact Spring: Stainless steel, passivated
Rotor Contact: Brass, silver over nickel plate
Common Ring: Brass, gold over silver over
nickel plate
Terminals: Brass, gold over silver over nickel
plate
Switch Base: Molded thermoset plastic
Mounting Hardware: One mounting nut .089"
thick by .375" across flats and one internal tooth
lockwasher are supplied with the switch.
Chartshownfornon-shorting(breakbeforemake)
contacts, resistive load.
300
200
100
0
Additional Characteristics
Contact Type and Forces: Shorting or non-
shorting wiping contacts with over 25 grams of
contactforce.
ShaftFlatOrientation:Flatoppositecontacting
positionofpolenumberone(seecircuitdiagrams).
Terminals: Switches have the full circle of
terminals,regardlessofnumberofactivepositions.
Stop Strength: 7.5 lb-in. minimum
Rotational Torque: 3.5 to 9 oz-in. (21-53 mN-
m), depending on the number of poles.
Bushing Mounting: Required for switches with
stops, and recommended for switches without
stops.
10
20
30
0
CYCLES x 1000
115 Vac 0r 30 Vdc
One cycle is 360° rotation clockwise and 360°
return. The data for the curve was measured at
sea level, 25°C and 68% relative humidity with
the life limiting criteria which follows.
Contact Resistance: 100 milliohms maximum,
(15 milliohms initially).
Insulation Resistance: 10,000 Mohms
minimum between mutually insulated parts
(50,000 Mohms initially).
Voltage Breakdown: 600 Vac minimum
between mutually insulated parts at standard
atmospheric pressure.
Meets MIL-S-3786 for:
High and medium shock; Vibration (10 to 2,000
Hz); Thermal shock (-65° to 85 ° C); Salt spray;
Explosion; Stop strength (7.5 in-lbs. minimum
(.85 N-m); Terminal strength; Sealed styles
withstand water pressure of 15 PSI minimum
(103 KPa) without leakage.
Life Expectancy: As determined from the load-
life curve for the current to be switched. Contact
GRAYHILL for more information if any of the
following is true: the life limiting criteria are more
Grayhill, Inc.
• 561 Hillgrove Avenue • LaGrange, Illinois 60525-5997 • USA • Phone: 708-354-1040 • Fax: 708-354-2820 • www.grayhill.com
J-23