485BAT3-3903-1/2
© 2003 by B&B Electronics. All rights reserved.
Model 485BAT3
Battery Powered RS-232 to
RS-422/485 Converter CE
Model 485BAT3 features power versatility, making it perfect for field testing
solutions. It converts unbalanced RS-232 signals to balanced RS-422 or RS-
485 signals. RS-485 is an enhanced version of the RS-422 standard, allowing
multiple drivers and receivers on a two-wire system.
Power
The 485BAT3 can be powered in three ways: batteries, port powered, or power supply. Use the battery power option
when you have a low power RS-232 port (found on many laptops today) or no handshake lines or when it is
inconvenient to use a power supply. Install 2 AAA batteries (not included) and put the Battery On/Off switch in the ON
position. The 485BAT3 will draw as much power as possible from the RS-232 port and get any additional current
necessary from the batteries.
If you have a full power port and all your handshake lines, turn off your battery switch. This allows you to run fully port
powered and saves your batteries for emergencies. NOTE: The Battery On-Off switch on the 485BAT3 is used for
conserving battery life. It does not turn on and off all power to the unit.
For your convenience there is the option to use a stripped and tinned +12VDC power supply. Simply attach it to the
terminal blocks and plug it in.
Switches
In addition to the Battery On/Off switch described in the Power section above there is a 2-position dipswitch on the top
of the 485BAT3. The position of these switches determines whether the signals on the terminal blocks are RS-422 or
RS-485. With both switches in the “Off” position the unit will act as a full duplex RS-232 to RS-422 converter. With both
switches in the “On” position, the unit acts as a half-duplex R-232 to RS-485 converter capable of multidropping on the
RS-485 side. When the RS-422/RS-485 switch is in the “RS-485” position, the 485BAT3 uses a bit-wise enable method
to control the RS-485 driver. This means that the RS-485 driver is enabled with each high bit transmitted. This method
requires no handshake control to activate and deactivate the driver. When the RS-422/RS-485 switch is in the “RS-422”
position the driver is constantly enabled.
The Echo On/Off switch controls the RS-485 receiver. When it is in the “On” position the receiver is constantly enabled.
When this switch is in the “Off” position the receiver is enabled only when the RS-485 driver is disabled for use in 2-wire
mode to prevent the transmitted data from echoing back on the RS-232 side.
Connections
Table 1: RS-232 Pinouts
The RS-232 port has a female DB9 connector with pins 2 (RD), 3 (TD), and 5
(Signal Ground) supported. Pins 7 (RTS) and 8 (CTS) are tied together, and
pins 6 (DSR), 1 (CD), and 4 (DTR) are also tied together. Any incoming data
lines in either the high or low state are used to port power the 485BAT3. The
more handshake lines available, the longer the battery life, and the more likely
the unit can be totally port powered. Table 1 shows the RS-232 pin outs.
RS - 232 Pinouts Description
1
2
3
4
5
6
7
8
DCD
RD
TD
DTR
GND
DSR
RTS
CTS
The RS-485 port uses terminal blocks for easy field wiring. TD A(-), TD B(+),
RD A(-), RD B(+), and Signal Ground lines are supported. Figure 1 shows how
to interconnect two RS-485 converters using two wires. Figure 1 shows how to
interconnect two RS-422 converters using four wires. Terminating resistors are
optional. They should be used only on long length runs or at high baud rates.
These resistors should match the impedance of the cable being used, which is
normally about 120 Ohms.
Up to 32 receivers can be driven by any one RS-485 driver, allowing you to put together large systems with many drop
points. If you are using termination resistors, they should be located at opposite ends of the system.
International Headquarters:
707 Dayton Road P.O. Box 1040 Ottawa, IL 61350 USA
815-433-5100 Fax 433-5104 www.bb-elec.com orders@bb-elec.com support@bb-elec.com
Westlink Commercial Park Oranmore Co. Galway Ireland
www.bb-europe.com orders@bb-elec.com support@bb-europe.com
+353 91 792444 Fax +353 91 792445
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
