Instruction Sheet
Pneumatic CERTI-CRIMP* Tool
Holder 356304-1 (For Use with 626
Pneumatic Tooling Assemblies)
408-4321
11 MAR 10 Rev C
Eccentric
Adjustment
Screw
Ratchet
Pawl
Cam
Setscrew
Cam
Adjustable
Eccentric
Tool Holder
Body
Applicable Crimp Head Adapters:
Pivot Pin
(4 Places)
Straight Action Crimper 217200-1
Heavy-Head Pneumatic Adapter 318453-1
Modular Plug Adapter 318510-1
Straight Action Crimp Head Adapter 217201-1
“T”-HEAD* Pneumatic Adapter 217202-1
C-Head Pneumatic Adapter 318161-1
Securing Screw (3 Places)
Figure 1
Air pressure must be removed from the tool while
head or tool holder is detached.
1. INTRODUCTION
DANGER
Pneumatic CERTI--CRIMP Tool Holder 356304--1 is
used in conjunction with 626 Pneumatic Tooling
Assemblies 189721--1 or 189722--1 to crimp various
types of connectors. The tool holder is designed to
accept interchangeable crimp head adapters (listed in
Figure 1) which hold various crimping die assemblies.
For questions concerning the setup and operation of
the pneumatic tools, refer to Customer Manual
409--5862.
If the piston is not extended, it must first be extended
to allow installation of the cam. To extend the piston,
firmly grasp the piston with piston pliers and pull away
from the body of the tool. Piston pliers are provided
with the power unit.
Read these instructions thoroughly before installing
the crimp head adapters and using the tool holder.
A strip of adhesive--backed safety labels, printed in
various languages, is packaged with the tool holder.
Remove the appropriate language label from the strip
and attach it to the tool holder body.
Dimensions are in millimeters [with inch
NOTE
equivalents in brackets]. Figures and illustrations
are for identification only and are not drawn to
scale.
i
Be sure to use the correct combination of cam
and tool holder. If incorrect combination is used,
system will not operate properly.
CAUTION
Reasons for reissue of this sheet are provided in
Section 7, REVISION SUMMARY.
!
2. DESCRIPTION (Figure 1)
The tool holder consists of a tool holder body, cam,
cam setscrew, adjustable eccentric, pivot pins, and
ratchet pawl with emergency release. The ratchet
ensures that the tool completes the crimp cycle.
Proceed as follows:
1. If cam setscrew is not installed in cam, thread
setscrew into cam two to three turns. See Figure 2.
3. INSTALLATION PROCEDURE
3.1. Tool Holder Installation
2. Place cam (with setscrew) onto piston rod. The
cam should butt against the piston rod face. If not,
turn cam setscrew counterclockwise until cam fits
on piston rod properly.
Previously installed cams and tool holders must
be removed before installing different ones.
Removal is the reverse of installation.
NOTE
3. Tighten cam setscrew, then pull on cam to
ensure that it is firmly attached.
i
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
1 of 4
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
5秒后页面跳转
摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
贸泽上架Tallysman TW5386智能GNSS天线
SL74HC10N：高性能三输入与非门解析
AIC1781A 电池充电控制器深度解析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
