5秒后页面跳转
24LC64I-SN PDF预览

24LC64I-SN

更新时间: 2024-01-29 16:03:37
品牌 Logo 应用领域
德州仪器 - TI 光电二极管
页数 文件大小 规格书
60页 3467K
描述
TLV320AIC3104EVM and TLV320AIC3104EVM-PDK

24LC64I-SN 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active零件包装代码:SOIC
包装说明:4.40 MM, ROHS COMPLIANT, PLASTIC, TSSOP-8针数:8
Reach Compliance Code:compliantECCN代码:EAR99
HTS代码:8542.32.00.51Factory Lead Time:6 weeks
风险等级:1.02Is Samacsys:N
其他特性:DATA RETENTION > 200 YEARS; 1000000 ERASE/WRITE CYCLES GUARANTEED最大时钟频率 (fCLK):0.4 MHz
数据保留时间-最小值:200耐久性:1000000 Write/Erase Cycles
I2C控制字节:1010DDDRJESD-30 代码:R-PDSO-G8
JESD-609代码:e3长度:4.4 mm
内存密度:65536 bit内存集成电路类型:EEPROM
内存宽度:8湿度敏感等级:1
功能数量:1端子数量:8
字数:8192 words字数代码:8000
工作模式:SYNCHRONOUS最高工作温度:85 °C
最低工作温度:-40 °C组织:8KX8
封装主体材料:PLASTIC/EPOXY封装代码:TSSOP
封装等效代码:TSSOP8,.25封装形状:RECTANGULAR
封装形式:SMALL OUTLINE, THIN PROFILE, SHRINK PITCH并行/串行:SERIAL
峰值回流温度(摄氏度):260电源:2/5 V
认证状态:Not Qualified座面最大高度:1.1 mm
串行总线类型:I2C最大待机电流:0.000001 A
子类别:EEPROMs最大压摆率:0.003 mA
最大供电电压 (Vsup):5.5 V最小供电电压 (Vsup):2.5 V
标称供电电压 (Vsup):5 V表面贴装:YES
技术:CMOS温度等级:INDUSTRIAL
端子面层:Matte Tin (Sn)端子形式:GULL WING
端子节距:0.65 mm端子位置:DUAL
处于峰值回流温度下的最长时间:40宽度:3 mm
最长写入周期时间 (tWC):5 ms写保护:HARDWARE
Base Number Matches:1

24LC64I-SN 数据手册

 浏览型号24LC64I-SN的Datasheet PDF文件第6页浏览型号24LC64I-SN的Datasheet PDF文件第7页浏览型号24LC64I-SN的Datasheet PDF文件第8页浏览型号24LC64I-SN的Datasheet PDF文件第10页浏览型号24LC64I-SN的Datasheet PDF文件第11页浏览型号24LC64I-SN的Datasheet PDF文件第12页 
www.ti.com  
TLV320AIC3104EVM Software  
4
TLV320AIC3104EVM Software  
The following section discusses the details and operation of the EVM software.  
Note: For configuration of the codec, the TLV320AIC3104 block diagram located in the  
TLV320AIC3104 data sheet is a good reference to help determine the signal routing.  
4.1 Device Selection for Operation With AIC3104EVM  
The software that is installed provides operation for several devices. An initial window should appear that  
looks like Figure 3. For operation with the TLV320AIC3104EVM, the user should select AIC3104 from the  
pulldown menu and click Accept. The software will take a few seconds to configure the software for  
operation before proceeding. A progress bar should appear and show the status of the configuration.  
Figure 3. Device Selection Window  
4.2 Interface Selection  
When the program first starts up, a small window (Figure 4) appears that gives two choices for the control  
interface: IC or SPI. Click on the interface that will be used by the EVM, as selected by the jumper settings  
detailed in Table 2. The setting of J10 should agree with the selection. 2C interface is the default interface  
used by the EVM.  
Figure 4. Interface Selection Window  
If the I2C interface is selected, a second window then appears which allows for selecting the address of  
the TLV320AIC3104. This window (see Figure 5) has two sliders for setting the state of A0 and A1. To  
allow proper communication with the EVM, these should match the settings of J11 and J12 (Table 2).  
When A0 and A1 are adjusted, the correct device address will be shown. Note that the actual I2C address  
shown and the address for the software may be different. This is done for programming reasons and the  
correct address should be used for system development .  
SLAU218August 2007  
TLV320AIC3104EVM and TLV320AIC3104EVM-PDK  
9
Submit Documentation Feedback  
 
 

与24LC64I-SN相关器件

型号 品牌 描述 获取价格 数据表
24LC64-IST MICROCHIP 64K I 2 C ⑩ CMOS Serial EEPROM

获取价格

24LC64-I-ST MICROCHIP 64K I2C™ Serial EEPROM

获取价格

24LC64-I-ST ARTSCHIP CMOS Serial EFPROM

获取价格

24LC64-IT/SN MICROCHIP 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8

获取价格

24LC64T MICROCHIP 64K I2C™ Serial EEPROM

获取价格

24LC64T/SM MICROCHIP 8K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8, 0.207 INCH, EIAJ, PLASTIC, SOIC-8

获取价格