HARTING Ha-VIS eCon Switches
5 to 7 Ethernet Ports RJ45, SC/LC (SFP) and PoE/PoE+ with 24 V DC/DC
Ha-VIS eCon 3000
Full Gigabit Ethernet Basic
PoE+ 24 V DC/DC
converter
Unmanaged Plug & Play Ethernet switches for DIN rail assembly in control
cabinets
Commercial Temp.: 0 °C ... +55 °C / Industrial Temp.: -40 °C ... +70 °C
Energy
Efficient
Ethernet
■ Use of PoE+ with 24 V DC supply (isolated)
■ Energy supply of up to 4 terminal devices via PoE+ (137 watts)
acc. to IEEE 802.3at
■ Full gigabit Ethernet, non-blocking switch architecture acc. to IEEE 802.3
■ Support of jumbo frames
■ Variants with industrial temperature range of -40°C ... +70 °C
■ Surge protection and reverse polarity protection
■ Minimum energy consumption due to Energy-Efficient Ethernet
■ Optimised DIN rail bracket
Target markets
Machinery &
Robotics
Wind Energy
Solar Energy
Industrial network
infrastructures
Automation technology
Transportation
Shipbuilding
General description
the switches are equipped with an integrated, galvanically isolated DC/DC
voltage transformer. The switches can be supplied with 24 VDC instead of
the usually required 54 VDC. Various combinations of variants with RJ45,
fibre optic cables and SFP ports are available. Automatic detection of the
transmission rate (auto-negotiation) and of the wiring of the twisted pair
data cable (autopolarity and auto-MDI(X)) allow for simple plug & play. All
variants are available with the temperature ranges „Industrial“ and
„Commercial“.
The Ha-VIS eCon 3000 Full Gigabit family of unmanaged Ethernet switches
is equipped with up to 7 gigabit Ethernet ports and allow for cost-efficient
and quick expansion and/or reconstruction of network infrastructures
with high bandwidth requirements. In this, all switches support extra-long
Ethernet frames (jumbo frames). The switches work as power sourcing
equipment (PSE) and are capable of simultaneously providing the full PoE
output of 34.2 watts on up to four ports. Exceeding the PoE+ standard,
Technical characteristics
Switch Features
Ethernet Ports 10BASE-Te / 100BASE-TX EEE / 1000BASE-T EEE
Connection type
Auto-negotiation
Auto-polarity
RJ45
Yes
Yes
Enclosures width
Number of ports
Switching technology
Supported standards
Frame Size
MAC table size
Packet buffer size
Non-blocking
60 mm
5, 6, 7
Store and Forward
IEEE 802.3
10 kbytes
8k entries
1 Mbit
Auto-MDI(X)
Yes
Transfer conditions
Transfer speed
Transfer length
Twisted Pair
10 / 100 / 1000 Mbit/s
100 m (twisted pair, Cat 5)
Yes
Quality of service
Energy-Efficient Ethernet
PROFINET compatible
EthernetIP compatible
Yes
Yes
Yes
Ethernet Ports 1000BASE-SX / 1000BASE-LX
Type of fibre
Multimode (MM)
Singlemode (SM)
SC Duplex
Connection type
Transfer conditions
Wavelength
Transfer speed
Transfer length
Output power
Input sensitivity
Yes
FO
850 nm
0.55 km
-9.5 dBm ... -4 dBm
≤ -17 dBm
1310 nm
1000 Mbit/s
10 km
-9.5 dBm ... -3 dBm
≤ -21 dBm
Voltage supply
Nominal voltage
Permissible voltage range
Surge protection
24 VDC
18 VDC ... 60 VDC
Yes
Reverse polarity proof
Starting current
Yes
1.60 A
SFP ports
Overcurrent protection at input
Max. power consumption @ 24 VDC
Cross-section / Wire gauge
Connection type
Yes (10 A)
Transfer standard
Connection type
Transfer conditions
Transfer speed
Depending on used SFP
141,2 W ... 141,6 W
0.08 mm² ... 2.5 mm² (28 AWG ... 12 AWG)
3-pole, pluggable screwed contact
+ / - /
Depending on used SFP, RJ45 or LC
Depending on used SFP, TP or FO
Depending on used SFP, 100 or 1000 Mbit/s
Depending on used SFP
Pinout
Transfer length
Supply circuit (acc. to 60950)
SELV (circuit breaker 10 A)
HARTING Technology Group
P.O.Box 1473, D-32325 Espelkamp
Wilhelm-Harting-Straße 1, D-32325 Espelkamp, Germany
Note: We reserve the right to make technical changes to the products and to the content of this
document at any time without prior notification. The HARTING Technologiegruppe does not accept
any responsibility for possible errors or incompletions in this document. We reserve all the rights to
this document and the topics and illustrations contained within it. Copying, disclosure to third parties
or use of its content - even partially - is forbidden without the prior written consent of the HARTING
Technologiegruppe.
ICPN-Service@harting.com | Service hotline: +49 5772 47-9479
Fax: +49 5772 47-495 | www.HARTING.com/de/ethernet-switches