5秒后页面跳转
2100TD PDF预览

2100TD

更新时间: 2024-09-30 06:17:15
品牌 Logo 应用领域
SYSTEMSENSOR 光电
页数 文件大小 规格书
4页 209K
描述
Photoelectronic Smoke Detectors

2100TD 数据手册

 浏览型号2100TD的Datasheet PDF文件第2页浏览型号2100TD的Datasheet PDF文件第3页浏览型号2100TD的Datasheet PDF文件第4页 
INSTALLATION AND MAINTENANCE INSTRUCTIONS  
2100D and 2100TD Photoelectronic  
Smoke Detectors  
A Division of Pittway  
3825 Ohio Avenue, St. Charles, Illinois 60174  
1-800-SENSOR2, FAX: 630-377-6495  
Specifications  
Diameter:  
5.5 inches (140 mm)  
Height (including mounting bracket):  
Weight:  
1.7 inches (43 mm)  
5.3 oz. (150 g)  
Operating Temperature Range:  
Model 2100D: 32° to 120°F (0° to 50°C)  
Model 2100TD: 32° to 100°F (0° to 39°C)  
Operating Humidity Range:  
Latching Alarm:  
10% to 93% Relative Humidity, Noncondensing  
Reset by momentary power interruption  
Heat Sensor (Model 2100TD only):  
Electrical Ratings  
135°F Fixed Temperature Electronic Thermistor  
System Voltage –  
Nominal:  
Minimum:  
Maximum:  
12 or 24 VDC  
8.5 VDC  
35 VDC  
Maximum Ripple Voltage:  
Start-up Capacitance:  
Standby Current:  
30% of nom. Voltage (peak to peak)  
0.02 µF maximum  
50 µA maximum  
Alarm Ratings:  
4.2 VDC minimum at 10 mA.  
6.6 VDC maximum at 100 mA.  
(Alarm current must be limited to 100 mA maximum by the control panel. If  
used, the RA400Z Remote Annunciator operates within the specified detector  
alarm currents.)  
Reset Voltage:  
Reset Time:  
2.5 VDC minimum  
0.3 seconds maximum  
Start-up Time:  
30 seconds maximum (after 60 second reset)  
Before Installing  
Please thoroughly read System Sensor manual I56-407, Installation of these detectors is simplified by the use of a  
Guide for Proper Use of System Smoke Detectors, which mounting bracket and a plug-in screw terminal block that  
provides detailed information on detector spacing, place- can be prewired to the system, allowing the detector to be  
ment, zoning, wiring, and special applications. Copies of easily installed or removed for cleaning. The detector’s  
this manual are available at no charge from System Sensor. sensitivity can be tested in place using the MOD400R Test  
Module. An LED on the detector provides a local visual  
NOTICE: This manual should be left with the owner/user indication of the detector’s status. If power is applied to  
of this equipment.  
the detector, and it is functioning normally in standby, the  
status LED blinks every ten seconds. The LED also latches  
IMPORTANT: This detector must be tested and maintained on in alarm.  
regularly following NFPA 72 requirements. The detector  
should be cleaned at least once a year.  
Models 2100D and 2100TD feature a visual indication that  
maintenance is required – if the sensing chamber drifts out  
of its sensitivity limits, the LED ceases to blink.  
General Description  
Model 2100D is a 2-wire photoelectronic smoke detector  
that uses a state-of-the-art optical sensing chamber. This The detectors also include an output that allows an optional  
detector is designed to provide open area protection and Model RA400Z Remote Annunciator to be connected.  
to be used with compatible UL-listed panels only. Model  
2100TD features a restorable, built-in, fixed-temperature  
(135°F) thermal detector.  
D200-54-00  
1
I56-710-09  

与2100TD相关器件

型号 品牌 获取价格 描述 数据表
2100TR SYSTEMSENSOR

获取价格

Photoelectronic Smoke Detector with Fixed Heat
2100TS SYSTEMSENSOR

获取价格

Smoke Detectors
2101 FRONTIER

获取价格

Insert Molded Coil
210-1000-FT10W RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 100ohm, 40V, 1% +/-Tol, 10ppm/Cel,
210-1002-FB10Q RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10000ohm, 40V, 1% +/-Tol, 10ppm/Cel,
210-1002-FB10W RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10000ohm, 40V, 1% +/-Tol, 10ppm/Cel,
210-1002-FBQ RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10000ohm, 40V, 1% +/-Tol, 20ppm/Cel,
210-100-HB5 RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10ohm, 40V, 3% +/-Tol, 5ppm/Cel,
210-100-HT5 RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10ohm, 40V, 3% +/-Tol, 5ppm/Cel,
210-100-JB10 RCD

获取价格

Fixed Resistor, Wire Wound, 2W, 10ohm, 40V, 5% +/-Tol, 10ppm/Cel,