10T6AW4_1.5 Series
10W - Dual/Single Output - 4:1 Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
10 Watt
4:1 wide input voltage range
Efficiency up to 88%
1500VDC/500VAC Isolation
Short circuit protection (SCP)
Input under-voltage, over-
current, over-voltage
protection
Operating temperature:
-40°C to +85°C
The 10T6AW4_1.5 series are isolated 10W DC-DC products with 4:1 input
voltage, 500VAC/1500VDC isolation, input under-voltage protection,
output over-voltage, over-current and short circuit protection, which
make them widely applied in industrial control, electricity, instruments
and communication fields.
Industry standard pinout
RoHS compliance
No-load power consumption
as low as 0.096W
Common specifications
Short circuit protection:
Temperature rise at full load:
Cooling:
Output specifications
Continuous, automatic recovery
40°C TYP
Item
Test condition
Min
Typ
±1
Max
±±
Units
%
Output voltage
accuracy
Free air convection
-40°C~+85°C
Line regulation
Full load, input voltage
from low to high
±0.2
±0.5
%
Operation temperature range:
Storage temperature range:
Pin welding resistance temperature:
-55°C ~+125°C
Load regulation
5% to 100% load
±0.5
±00
±1.0
500
%
±00°C MAX, 1.5mm from case for 10 sec
Transient recovery
time
25% load step change
µs
Reflow soldering temperature:
(Only for models with housing)
Peak temp. ≤245°C, maximum duration
time ≤60s at 217°C. For actual
application, please refer to IPC/JEDEC
J-STD-020D.1.
Transient response
deviation
25% load step change
100% load
±±
±5
%
Temperature
coefficient
±0.0±
100
%/°C
Vibration:
10-55Hz, 10G, ±0 Min. along X, Y and Z
< 95%
Storage humidity range:
Case material:
MTBF:
Ripple & Noise*
Trim
20MHz Bandwidth
50
±5
mVp-p
%Vo
Aluminium Alloy
Nominal input voltage
Input voltage range
>1,000,000 hours
Over Voltage
Protection
110
110
160
%Vo
Weight:
6.7g /5.7g (without case)
Over Voltage
Protection
Input voltage range
140
±50
200
%Io
Input specifications
Switching frequency** PWM mode
KHz
Item
Test condition
Min
Typ
Max
Units
*
Test ripple and noise by “parallel cable” method. See detailed operation
instructions at Testing of Power Converter section, application notes.
Input current
(full load / no load)
Nominal input
voltage
• 5VDC input
• 12VDC input
• 15VDC input
** This series of products using reduced frequency technology, the switching
frequency is test value of full load. When the load is reduced to below 50%, the
switching frequency decreases with decreasing load.
496/4
479/±
474/4
508/40
490/12
485/15
mA
mA
mA
Reflected ripple
current
Nominal input
voltage
40
mA
Isolation specifications
Item
Test condition
Min
Typ
Max
Units
Surge voltage
Starting voltage
Shutdown voltage
Input filter
1sec. max.
-0.7
5.5
50
9
VDC
VDC
VDC
Isolation voltage
(Tested for 1 minute
and leakage current
less than 5mA)
• Input-output
• Input/Output-case
(for models with case)
1500
1500
VDC
VDC
6.5
• Input-output
• Input/Output-case
(for models with case)
500
500
VAC
VAC
Pi
Hot plug
unavailable
• Models ON
Ctrl*
Ctrl pin connected to GND or low
level (0-1.2VDC)
Ctrl pin suspended or connected to
High level (2.4-12VDC)
6mA (TYP)
Isolation resistance
(Test at 500VDC)
• Input-output
• Input/Output-case
(for models with case)
1000
MΩ
pF
(operating
temperature range)
• Models OFF
Isolation capacitance
Input/Output,
100KHz/0.1V
1000
• Input current
when switched
off (@25°C)
* The voltage of Ctrl pin is relative to input pin GND.
Example:
10T6AW4_2405S1.5
10= 10Watt; T6= SMT6; A= series; W4= wide input (4:1) 9-36Vin;
5Vout; S= Single output; 1.5= 1500VDC
Page 1 of 5
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com
10T6AW4_1.5 – Rev. 2019-1.0
Specifications subject to change without notice.