Datasheet > 09-06-2077

09-06-2077

更新时间： 2022-03-29 07:46:08

品牌	Logo	应用领域
莫仕 - MOLEX		/
页数	文件大小	规格书
6页	171K
描述
IDT CHANGE HEAD Specification Sheet

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

09-06-2077 数据手册

Change head for IDT Connectors Series

RIB OF CONNECTOR FACING UP

2. Place the proper connector into the track; the rib of the connector should be facing up. See

Figure 3.

3. Compress the front pistol handle and slide the connector into the Change Head track until it

stops, release the pistol handle.

4. Operate the pistol to index the connector into the change head.

5. Place the proper wire into the slot above the connector. Make sure that the wire is fully seated.

6. Close the piston hand tool by moving the front operating handle while holding the wire in place.

7. Release the operating handle gently. During the return stroke the housing will automatically

advance to the next circuit position.

8. Check for wire insulation depth in the location slot. The wire insulation must be just below the

“eagle” of the connector housing. See Figure 4.

9. Repeat steps 4 thru 7 above for placement of additional wires until the last circuit of the

housing is completed.

10. To remove the completed wire/housing assembly from the piston hand tool, slide the assembly

Figure 3

TRACK

to the right and push out.

Note: After the last wire insertion has been made in the connector assembly, the assembly will not advance any further because the

feed pawl will have cleared the end of the connector body.

EAGLE

ADJUSTMENTS

Wire Insertion Depth

1. Remove the Change Head from the pistol handle.

2. To adjust the insertion depth of the wire use the Allen wrench which is included with Change

Head.

3. Place the Allen wrench into the feed adjustment set screw, which is located in the mounting

slot of the change head that goes into the piston handle. See Figure 1.

4. By rotating this setscrew, the insertion depth can be changed.

5. Clockwise (CW) will increase wire insertion depth. Counter Clockwise (CCW) will decrease wire

WIRE

CONNECTOR

HOUSING

insertion depth.

Figure 4

Guide Plate

The two fixing screws on the front guide plate offer a small amount of track adjustment. This should only be adjusted if the connector

does not run smoothly through the track.

Connector Locator

The small slotted spring ball screw in the body molding of the change head is used to adjust the connector locator.

1. The spring ball screw should be loosened for 2,3,4, and 5 circuits size connector housings using a 3mm wide screwdriver blade.

See Figure 1.

2. For larger circuit size connector housing the spring ball screw should be tightened. This will ensure correct and consistent feed

action during operation.

This is set at the factory and should not require adjustment.

Doc No. 011215196

Revision: A

Release Date: 05-15-06

Revision Date: 05-15-06

UNCONTROLLED COPY

Page 5 of 6

1 2 3 456

下载PDF

与09-06-2077相关器件

型号	品牌	描述	获取价格	数据表
09-06-2078	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-2079	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-2080	MOLEX	3.96mm (.156") KK® IDT Trifurcon™ Contact, 8	获取价格
09-06-2087	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-2088	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-2089	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格