Embossed Carrier Configuration
8 & 12mm Tape Only
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
0.2mm ( 0.008)
EMBOSSMENT
P0
T2
T
D0
P2
DEFORMATION
BETWEEN
EMBOSSMENTS
E1
A0
W
F
E2
TOP COVER
TAPE
B1
B0
P1
K0
T1
D1 FOR COMPONENTS
2.00 mm x 1.20 mm AND
LARGER (0.079 x 0.047)
CENTER LINES
OF CAVITY
S1
MAX. CAVITY
SIZE - SEE NOTE 1
B1 IS FOR TAPE READER REFERENCE ONLY
INCLUDING DRAFT CONCENTRIC AROUND B0
User Direction of Feed
8 & 12mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
D0
E
P0
P2
S1 Min.
T Max.
T1
8mm
and
12mm
1.50 -+00..010
1.75 0.10
4.0 0.10
2.0 0.05
0.60
(0.024)
0.60
(0.024)
0.10
(0.004)
Max.
(0.059 +-00..0004
)
(0.069 0.004) (0.157 0.004) (0.079 0.002)
VARIABLE DIMENSIONS
Tape Size
B1
Max.
D1
Min.
E2
Min.
F
P1
R
T2
W
Max.
A0 B0 K0
Min.
See Note 5 See Note 2
4.35
1.00
6.25
3.50 0.05
4.00 0.10
25.0
2.50 Max.
(0.098)
8.30
8mm
See Note 1
See Note 1
See Note 1
See Note 1
(0.171)
(0.039)
(0.246) (0.138 0.002) (0.157 0.004)
(0.984)
(0.327)
8.20
(0.323)
1.50
(0.059)
10.25
5.50 0.05
4.00 0.10
30.0
(1.181)
6.50 Max.
(0.256)
12.3
(0.484)
12mm
(0.404) (0.217 0.002) (0.157 0.004)
8mm
1/2 Pitch
4.35
(0.171)
1.00
(0.039)
6.25
3.50 0.05
2.00 0.10
25.0
(0.984)
2.50 Max.
(0.098)
8.30
(0.327)
(0.246) (0.138 0.002) (0.079 0.004)
12mm
Double
Pitch
8.20
(0.323)
1.50
(0.059)
10.25
5.50 0.05
8.00 0.10
30.0
(1.181)
6.50 Max.
(0.256)
12.3
(0.484)
(0.404) (0.217 0.002) (0.315 0.004)
NOTES:
2. Tape with or without components shall pass around radius “R” without damage.
1. The cavity defined by A0, B0, and K0 shall be configured to provide the following:
Surround the component with sufficient clearance such that:
3. Bar code labeling (if required) shall be on the side of the reel opposite the round sprocket holes.
Refer to EIA-556.
a) the component does not protrude beyond the sealing plane of the cover tape.
b) the component can be removed from the cavity in a vertical direction without mechanical
restriction, after the cover tape has been removed.
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. If P1 = 2.0mm, the tape may not properly index in all tape feeders.
c) rotation of the component is limited to 20º maximum (see Sketches D & E).
d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch F).
Top View, Sketch "F"
Component Lateral Movements
0.50mm (0.020)
Maximum
0.50mm (0.020)
Maximum
48