8.5-11.0 GHz GaAs Power Amplifier
Flange, 10 pin
August 2006 - Rev 16-Aug-06
P1006-FA
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the
environment. For safety, observe the following procedures:
• Do not ingest.
• Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-products are
dangerous to the human body if inhaled, ingested, or swallowed.
• Observe government laws and company regulations when discarding this product.This product must be discarded in accordance with methods
specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems
without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or
systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a
significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Mounting Onto Circuit Boards - Special design considerations allow the –FA packages to operate at high frequencies. One element required
for operation at high frequency is the use of fine geometry leads. Fine geometry leads are not as robust, and it is possible to exceed the yield
or tensile strength even with small hand tools. Even though firmly attached, EXTRA care in handling is essential.
Precautions:
• Check all fixtures used for assembly, lead forming, and testing, to be sure that parts are not subjected to unnecessary physical stress.
• Check that test sockets are easy to load, and not likely to torque or twist the leads.
• Be sure that the package is attached to a flat surface.
• Do not over-torque mounting screws.
• Do not use conductive gaskets or shims under the package.
• Do not use test fixtures or sockets that may produce a sharp lifting force on the leads.
• If packages must be removed after solder attach, do not pry the leads up so that the force lifting the lead from the board is also lifting the lead from
the package. Use a probe to press down on the lead-to-package joint, and lift the lead when the solder is fluid.
Mounting Screws -
Product Name
Socket Head Cap
Screw, English
Length, min
Diameter
Thread Pitch
Material
Type 316
Torque, in-oz
1/8"
0
80
1.0
Stainless Steel
Type 316
Socket Head Cap
Screw, English
1/8"
6 mm
6 mm
2
56
2.0
1.0
2.0
Stainless Steel
Type 316
Socket Head Cap
Screw, Metric
M1.6
M2.5
0.35mm
0.45mm
Stainless Steel
Type 316
Socket Head Cap
Screw, Metric
Stainless Steel
1. Mounting surface should be tapped for close tolerance fit of inner to external thread
2. Mounting surface must be flat
3. Excessive bending or deformation of the package during mounting is likely to damage the ceramic. To avoid this:
• Insert all mounting screws for a given package and tighten all finger tight.
• Begin tightening screws on opposite corners of the package to 1/3 torque
• Tighten following same screw position pattern to 2/3 torque
• Tighten following same screw position pattern to full torque
4.The use of ground or thermal pads under the package is NOT recommended.
Ordering Information
Part Number for Ordering
XP1006-FA-0N00
XP1006-FA-EV1
Description
Nickel/Gold plated RoHS compliant 10L flange package in bulk quantity
XP1006-FA Evaluation Module
Page 6 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2006 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
5秒后页面跳转
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
CD4052资料手册参数详解、引脚配置说明
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
