ELECTRICAL CHARACTERISTICS
Electrical characteristics apply over the full operating range of input voltage, output load (resistive) and baseplate temperature,
unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate.
MODULE OPERATING SPECIFICATIONS
Parameter
Min
Typ
Max
425
500
1
Unit
Vdc
Vdc
Notes
Operating input voltage
Input surge withstand
250
375
<100ms
Output voltage setpoint
% Vout nom
Nominal input; full load; 25°C
MODULE OUTPUT VOLTAGE RELATED SPECIFICATIONS
Parameter
1.8V1 2V
2.5V2 3.3V
5V
12V
15V 24V 28V
48V
Unit
Notes
Efficiency (typ.)
73
70
74.5
70
76
70
80
80
83.5 85.7
102 120
400 600
87
90
88
92
89
90
%
Nominal input; 80% load; 25°C
Nominal input; full load;
25°C; 20MHz BW
Ripple and noise, p-p (typ.)
Output Power (max.)
160
50
mV
144
160
2.8
200 264
600 600 600
600
Watts
At 100°C baseplate temperature
25°C; recycle input voltage to
restart ( 1 minute off )
Output OVP setpoint (nom.) 2.8
4.3
4.3
6.3 14.3 17.8 28.1 32.7
55.2
6.0
Volts
Dissipation, standby (typ.)
Load regulation (max.)
Current limit (typ.)
5.0
0.2
115
5.0
0.2
115
4.9
0.2
4.9
0.2
5.0
0.2
8.7
0.2
8.0
0.2
8.5
0.2
8.0
0.2
Watts
No load; nominal input
0.2 ±% Vout
No load to full load; nominal input
Output voltage 95% of nominal
115 115
115 115
115 115
115 115
115 115 115
115 115 115
115
115
% Iout
% Iout
Short circuit current (typ.)
115
115
Output voltage <250mV
MODULE INPUT SPECIFICATIONS
Parameter
Min
Typ
Max
Unit
Vdc
Vdc
Vdc
Notes
Undervoltage turn-on
Undervoltage turn-off
Overvoltage turn-off/on
242.5
212.2
446.3
247.5
204.7
429.2
467.5
MODULE OUTPUT SPECIFICATIONS
Parameter
Min
Typ
±0.02
±0.002
±2
Max
±0.2
Unit
%
Notes
Line regulation
Low line to high line; full load
-20 to 100°C
Temperature regulation
Power sharing accuracy
±0.005
±5
% / °C
%
10 to 100% of full load
Of nominal output voltage. For trim below 90%
of nominal, a minimum load of 10% of maximum
rated power may be required.
Programming range
10
110
%
Note: For important information relative to applications where the converter modules are subject to continuous dynamic loading,
contact Vicor Applications Engineering at 800-927-9474.
1 Nominal 2V output trimmed to 1.8V by adding external 9,000 ohm resistor from the SC pin to
-S pin. (See Fig. 7)
2 Nominal 3.3V output trimmed to 2.5V by adding external 3,125 ohm resistor from the SC pin to
-S pin. (See Fig. 7)
Vicor Corporation Tel: 800-735-6200 • 978-470-2900 • Fax: 978-475-6715
Page 2 of 8
The latest data sheets for individual models are available on the Vicor website at www.vicr.com