ALUMINUM ELECTROLYTIC CAPACITORS
Chip Type, High Voltage.
Long Life.
ULV
Chip Type, high voltage and long life.
Load life of 10000 hours at +105°C
Applicable to automatic mounting machine using carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Long Life
ULR
ULV
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
–40 to +105°C
160 to 500V
1.8 to 33µF
20% at 120Hz, 20°C
Rated voltage (V)
–
160 to 450
500
Leakage Current
0.04CV+100(µA)max.(1 minute's at 20°C) 0.04CV+200(µA)max.(1 minute's at 20°C)
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
160
0.20
200
0.20
250
0.25
400
0.25
450
0.30
500
0.30
Tangent of loss angle (tan δ)
Measurement frequency: 120Hz
Rated voltage (V)
250
10
400
10
450
15
500
15
160
6
200
Stability at Low Temperature
Impedance ratio
ZT / Z20 (MAX.)
6
Z–40°C / Z+20°C
Capacitance change
tan δ
Leakage current
Within 30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 10000 hours at 105°C.
Endurance
Shelf Life
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change
tan δ
Leakage current
Within 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Resistance to soldering
heat
maintained at 250°C and then performing voltage treatment based on
JIS C 5101-4 clause 4.1 at 20°C, they shall meet the characteristic
requirements listed at right when they are removed from the plate.
Marking
Black print on the case top.
Chip Type
(φ8 , φ10)
Voltage(2G : 400V)
Series
Type numbering system (Example : 400V 6.8 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
Plastic platform
U L V 2 G 6 R 8 M N L 1 G S
C
0.2
0.3MAX.
Lot No.
Taping code
Configuration
Capacitance tolerance ( 20ꢀ)
Trade mark
Rated capacitance
Rated voltage
(
6.8µF
)
)
Capacitance
H
L
1.0
Negative
(
400V
Pressure relief vent
(mm)
φD × L
Series name
Type
8 × 10
2.9
8.3
8.3
3.1
10
10 × 10 10 × 13.5
A
3.2
10.3
10.3
4.5
3.2
10.3
10.3
4.5
B
C
E
L
Voltage
V
160 200 250 400 450 500
2C 2D 2E 2G 2W 2H
10
13.5
H
0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Code
Dimensions
V
160
2C
200
2D
250
400
450
500
2H
Cap.(µF)
1.8
3.3
3.9
4.7
5.6
6.8
7.5
8.2
10
Code
2E
2G
2W
1R8
3R3
3R9
4R7
5R6
6R8
7R5
8R2
100
120
150
180
220
270
330
8 × 10
25
40
8 × 10
25
10 × 10
8 × 10
35
50
55
10 × 13.5
45
10 × 10
40
45
10 × 10
10 × 13.5
8 × 10
35
10 × 13.5
12
8 × 10
50
65
70
15
8 × 10
10 × 10
10 × 13.5
50
65
70
10 × 10
50
55
18
10 × 10
10 × 13.5
22
27
10 × 13.5
Rated
ripple
Case size
φ D × L (mm)
33
Rated ripple current (mArms) at 105°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz 300 Hz
1 kHz 10 kHz or more
Please refer to page 3 for the minimum order quantity.
Coefficient
0.80
1.00 1.25
1.40
1.60
159