Datasheet > UF03N1R0B101

UF03N1R0B101

更新时间： 2024-04-09 18:56:08

品牌	Logo	应用领域
华新科技 - WALSIN		/
页数	文件大小	规格书
9页	2729K
描述
0201, NPO, 1.0pF, 100Vdc

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

UF03N1R0B101 数据手册

Multilayer Ceramic Capacitors

Approval Sheet

9. RELIABILITY TEST CONDITIONS AND REQUIREMENTS

No.

Item

Test Conditions

Requirements

1. Visual and

Mechanical

---

* No remarkable defect.

* Dimensions to conform to individual specification sheet.

2. Capacitance

3. Q/ D.F.

(Dissipation

Factor)

* Test temp.: Room Temperature.

1.0±0.2Vrms, 1MHz±10%

* Shall not exceed the limits given in the detailed spec.

* Cap.=0.05pF: Q≥300

* 0.1pF≤Cap.<30pF: Q≥400+20C

*To apply voltage: 250% of rated voltage.

*Duration: 1 to 5 sec.

4. Dielectric

Strength

* No evidence of damage or flash over during test.

*Charge & discharge current less than 50mA.

5. Insulation

Resistance

* Test temp.: Room Temperature.

≥10GΩ or RxC≥100Ω-F whichever is smaller

* To apply rated voltage for max. 120 sec.

6. Temperature

Coefficient

With no electrical load.

* Capacitance change: within ±30ppm/°C;

Operating temperature: -55~125°C at 25°C

7. Adhesive

Strength of

Termination

* Pressurizing force：

* No remarkable damage or removal of the terminations.

0201: 2N

0402: 5N

* Test time: 10±1 sec.

8. Vibration

Resistance

* Vibration frequency: 10~55 Hz/min.

* Total amplitude: 1.5mm

* No remarkable damage.

* Cap change and Q/D.F.: To meet initial spec.

* Test time: 6 hrs. (Two hrs each in three mutually

perpendicular directions.)

*Cap./DF(Q) Measurement to be made after de-aging at 150°C

for 1hr then set for 24±2 hrs at room temp.

* Solder temperature: 235±5°C

* Dipping time: 2±0.5 sec.

9. Solderability

95% min. coverage of all metalized area.

10. Bending Test * The middle part of substrate shall be pressurized by means * No remarkable damage.

of the pressurizing rod at a rate of about 1 mm per second until * Cap change: within ±5.0% or ±0.5pF whichever is larger.

the deflection becomes 1 mm and then the pressure shall be

maintained for 5±1 sec.

(This capacitance change means the change of capacitance under

specified flexure of substrate from the capacitance measured before

the test.)

* Measurement to be made after keeping at room temp. for

24±2 hrs.

11. Resistance to * Solder temperature: 260±5°C

Soldering Heat * Dipping time: 10±1 sec

* Preheating: 120 to 150°C for 1 minute before imme rse the

* No remarkable damage.

* Cap change: within ±2.5% or ±0.25pF whichever is larger.

* Q/D.F., I.R. and dielectric strength: To meet initial requirements.

* 25% max. leaching on each edge.

capacitor in a eutectic solder.

*Cap. / DF(Q) / I.R. Measurement to be made after de-aging at

150°C for 1hr then set for 24±2 hrs at room temp.

* "Room condition" Temperature: 15 to 35°C, Relativ e humidity: 25 to 75%, Atmospheric pressure: 86 to 106kPa.

Page 5 of 9

ASC_Microwave_Narrow_Tol_UF

May. 2023

1 2 3 456 7 8 9

下载PDF

与UF03N1R0B101相关器件

型号	品牌	描述	获取价格	数据表
UF03N1R0C101	WALSIN	0201, NPO, 1.0pF, 100Vdc	获取价格
UF03N1R0P101	WALSIN	0201, NPO, 1.0pF, 100Vdc	获取价格
UF03N1R0P250	WALSIN	0201, NPO, 1.0pF, 25Vdc	获取价格
UF03N1R0P500	WALSIN	0201, NPO, 1.0pF, 50Vdc	获取价格
UF03N1R0Q500	WALSIN	0201, NPO, 1.0pF, 50Vdc	获取价格
UF03N1R2A250	WALSIN	0201, NPO, 1.2pF, 25Vdc	获取价格