TPS61010, TPS61011
TPS61012, TPS61013
DGS
DRC
TPS61014, TPS61015, TPS61016
www.ti.com
SLVS314D–SEPTEMBER 2000–REVISED JUNE 2005
HIGH-EFFICIENCY, 1-CELL AND 2-CELL BOOST CONVERTERS
The converter output voltage can be adjusted from
FEATURES
1.5 V to a maximum of 3.3 V, by an external resistor
divider or, is fixed internally on the chip. The devices
provide an output current of 200 mA with a supply
voltage of only 0.9 V. The converter starts up into a
full load with a supply voltage of only 0.9 V and stays
in operation with supply voltages down to 0.8 V.
•
Integrated Synchronous Rectifier for Highest
Power Conversion Efficiency (>95%)
•
Start-Up Into Full Load With Supply Voltages
as Low as 0.9 V, Operating Down to 0.8 V
•
•
200-mA Output Current From 0.9-V Supply
Powersave-Mode for Improved Efficiency at
Low Output Currents
The converter is based on a fixed frequency, current
mode, pulse-width-modulation (PWM) controller that
goes automatically into power save mode at light
load. It uses a built-in synchronous rectifier, so, no
external Schottky diode is required and the system
efficiency is improved. The current through the switch
is limited to a maximum value of 1300 mA. The
converter can be disabled to minimize battery drain.
During shutdown, the load is completely isolated from
the battery.
•
Autodischarge Allows to Discharge Output
Capacitor During Shutdown
•
•
Device Quiescent Current Less Than 50 µA
Ease-of-Use Through Isolation of Load From
Battery During Shutdown of Converter
•
•
•
Integrated Antiringing Switch Across Inductor
Integrated Low Battery Comparator
An autodischarge function allows discharging the
output capacitor during shutdown mode. This is
especially useful when a microcontroller or memory is
supplied, where residual voltage across the output
capacitor can cause malfunction of the applications.
When programming the ADEN-pin, the autodischarge
function can be disabled. A low-EMI mode is im-
plemented to reduce interference and radiated elec-
tromagnetic energy when the converter enters the
discontinuous conduction mode. The device is pack-
aged in the micro-small space saving 10-pin MSOP
package. The TPS61010 is also available in a 3 mm
x 3 mm 10-pin QFN package.
Micro-Small 10-Pin MSOP or 3 mm x 3 mm
QFN Package
•
EVM Available (TPS6101xEVM-157)
APPLICATIONS
•
All Single- or Dual-Cell Battery Operated Prod-
ucts Like Internet Audio Players, Pager, Port-
able Medical Diagnostic Equipment, Remote
Control, Wireless Headsets
DESCRIPTION
The TPS6101x devices are boost converters intended
for systems that are typically operated from a single-
or dual-cell nickel-cadmium (NiCd), nickel-metal hy-
dride (NiMH), or alkaline battery.
L1
10 mH
C
IN
7
10 mF
SW
5
6
VBAT
VOUT
VOUT = 3.3 V
C
OUT
R3
22 mF
R1
9
10
LBI
LBO
Low Battery
Warning
R2
TPS61016
ON 1
3
OFF
EN
FB
R
C
100 kW
ON 8
2
OFF
COMP
ADEN
GND
C
C1
C
C2
4
10 pF
10 nF
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2000–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.