5秒后页面跳转
SP8107EH-L PDF预览

SP8107EH-L

更新时间: 2024-10-01 13:13:55
品牌 Logo 应用领域
西伯斯 - SIPEX 驱动器
页数 文件大小 规格书
3页 147K
描述
暂无描述

SP8107EH-L 数据手册

 浏览型号SP8107EH-L的Datasheet PDF文件第2页浏览型号SP8107EH-L的Datasheet PDF文件第3页 
Advanced  
SP8107  
Three Channel High Performance Laser Driver  
FEATURES  
Three current controlled inputs with independent  
ENABLE/DISABLE  
Two selectable outputs for grounded laser diodes  
Output current up to 400mA (250mA per input channel)  
Independent swing for each output channel controlled  
by external resistor  
On-chip oscillator with resistor controlled frequency  
Single 5V power supply  
Common ENABLE and oscillator ENABLE inputs  
TTL/CMOS logic level control signals  
Small SSOP16 package  
IR  
I2  
Vcc  
1
2
3
4
5
6
7
8
16  
15  
14  
13  
12  
11  
10  
9
Iout A  
GND  
RSA  
RSB  
I3  
RF  
SP8107  
SSOP-16  
EN2  
EN3  
Iout B  
SELA  
Vcc  
APPLICATION  
ENABLE  
OSCEN  
DVD-RAM with CD-RW capability  
DVD-RW with CD-RW capability  
Writable data storage optical devices  
GENERAL DESCRIPTION  
The SP8107 is a three channel laser diode driver specifically designed for high speed DVD-RW or DVD-  
RAM applications. It operates two grounded laser diodes (650nm for DVD and 780nm for CD) and  
features three input channels that allow setting of three different optical power levels. The first channel  
(IR) has lower gain (100mA/mA) and output current (up to 200mA) and is used as a read channel. The  
second (I2) and third (I3) channels have higher gain (250mA/mA) and output current (up to 250mA) and  
are used as write channels. Each write channel may be switched on/off at very fast switching speeds with  
TTL/CMOS logic level signals applied to EN2 and EN3 inputs - channels are enabled at low logic level  
and disabled at high logic level. Outputs of all channels are summed together and connected to one of the  
outputs IOUT A or IOUT B depending on logic signal at the input SELA. High logic level at SELA selects  
output IOUT A, while low logic level selects output IOUT B. Inputs IR, I2, and I3 are current-controlled with  
200 ohm DC impedance but allow voltage control by using external limiting resistors.  
An on-chip oscillator is used to reduce laser mode hopping in read mode. The frequency of this oscillator  
may be changed by an external resistor connected to the RF pin. Oscillator swing can be set separately for  
I
OUT A and IOUT B outputs by two resistors connected to RSA and RSB pins respectively. The oscillator is  
enabled by high logic level at the OSCEN pin.  
Low logic level at the ENABLE pin disables the entire device. Supply current in disabled mode is below  
100uA. Pins EN2 and EN3 have internal pull-up resistors. Pins ENABLE, OSCEN, and SELA have  
internal pull-down resistors.  
Rev. 09/05/03  
SP8107 – Three Channel Laser Driver  
Copyright 2003 Sipex Corporation  
SIPEX RESERVES THE RIGHT TO MAKE CHANGES TO THIS DATASHEET. CALL FOR UPDATES: 1-978-667-8700.  
SIPEX CONFIDENTIAL, ADVANCED & PROPRIETARY. DO NOT DISTRIBUTE OR  
COPY  
page 1 of 3  

与SP8107EH-L相关器件

型号 品牌 获取价格 描述 数据表
SP810EK-2.3/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, TO-236AB, SOT-23, 3 PIN
SP810EK-2.3-L/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, LEAD FREE, SOT-23, 3 PIN
SP810EK-2.6/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, TO-236AB, SOT-23, 3 PIN
SP810EK-2.6-L SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, LEAD FREE, SOT-23, 3 PIN
SP810EK-2.6-L/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, LEAD FREE, SOT-23, 3 PIN
SP810EK-2.9/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, TO-236AB, SOT-23, 3 PIN
SP810EK-2.9-L SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, LEAD FREE, SOT-23, 3 PIN
SP810EK-2.9-L/TR SIPEX

获取价格

Power Supply Support Circuit, Fixed, 1 Channel, PDSO3, LEAD FREE, SOT-23, 3 PIN
SP810EK-2-3 SIPEX

获取价格

3 Pin Microprocessor Supervisor Circuit
SP810EK-2-3/TR SIPEX

获取价格

3 Pin Microprocessor Supervisor Circuit