Datasheet
Standard Products
RDC5028C 16-Bit Monolithic Tracking
Rad Tolerant Resolver-To-Digital Converter
www.aeroflex.com/RDC
May 7, 2014
FEATURES
Enhanced version of the ACT5028B
Radiation performance
- Total dose: 1 Mrad(Si), Dose rate = 50 - 300 rads(Si)/s
- SEL:Immune up to 100 MeV-cm2/mg
+5VDC power only
Programmable: By using a few non critical external resistors and capacitors
- Resolution: 10, 12, 14 or 16 bit resolution
- Bandwidth
- Tracking rate
Low power: +5V @ 20 mA typ
45 to 30,000 Hz carrier frequency range
Accuracy:
- 10.0 Arc Minutes if not compensated by INL correction factors.
- 5.3 Arc Minutes using INL correction factors.
Differential instrument amplifiers resolver input
-55° to +125°C operating temperature
Digital interface logic voltage of 3.3V to 5V
Designed for aerospace and high reliability space applications
Packaging – Hermetic
- 52 Pin Ceramic QUAD flat package (CQFP), .956" SQ x .100"Ht
- Weight: 5.0g max
Evaluation board available for test and evaluation. See Aeroflex Application note AN5028-1
Aeroflex Plainview’s Radiation Hardness Assurance Plan is DLA Certified to MIL-PRF-38534, Appendix G.
APPLICATIONS
This single chip Resolver-to-Digital Converter (RDC) is used in shaft angle control systems, and is suitable for space
or other radiation environments that require > 1 Mrad(Si) total dose tolerance. The part is latchup free in heavy ion
environments (e.g., geosynchronous orbits) and is estimated to experience SEU induced errors of less than 15 minutes
of arc at a rate of 1 per device per 2 years when operating dynamically.
THEORY OF OPERATION
The RDC5028 converter is a single CMOS Type II tracking resolver to digital converter monolithic chip. It is
implemented using precision analog circuitry and digital logic. For flexibility, the converter bandwidth, dynamics and
velocity scaling are externally set with passive components. Refer to Figure 1, RDC5028 Block Diagram.
The converter is powered from +5VDC. Analog signals are referenced to signal ground, which is nominally VCC/2.
The converter consists of three main sections; the Analog Control Transformer (CT), the Analog Error Processor (EP)
and the Digital Logic Interface.
The CT has two analog resolver inputs (Sin and Cos) that are buffered by high impedance input instrumentation type
amplifiers and the 16 bit digital word which represents the output digital angle. The CT performs the ratiometric
trigonometric computation of:
SIN(A) sin(wt) COS(B) – COS(A) sin(wt) SIN(B) = SIN(A-B) sin(wt)
Utilizing amplifiers, switches, logic and resistors in precision ratios. “A” represents the resolver angle, “B“ represents
the digital angle and sin(wt) represents the resolver reference carrier frequency.
The Error Processor is configured as a critically damped Type II loop. The AC error, SIN (A-B) sin (wt) is full wave
demodulated using the reference squared off as its drive. This DC error is integrated in an analog integrator yielding a
velocity voltage which in turn drives a Voltage Controlled Oscillator (VCO). Note in the block diagram, hysterisis is
added to prevent dithering and disables counting when the error is less than 1 LSB. This VCO is an incremental
integrator (constant voltage input to position rate output) which, together with the velocity integrator, forms a Type II
loop. A lead is inserted to stabilize the loop and a lag is inserted at a higher frequency to attenuate the carrier
frequency ripple. The error processor drives the 16 bit digital output until it nulls out. Then angle “A” = “B”. The
digital output equals angle input to the accuracy of the precision control transformer. The various error processor
settings are done with external resistors and capacitors so that the converter loop dynamics can be easily controlled by
the user.The digital logic interface has a separate power line, VLI/O that sets the interface logic 1 level. It can be set
anywhere from +3V to the +5V power supply.
SCD5028-2 Rev G
高通公司涉嫌违反反垄断法 回应称正积极配合调查
芯盛智能重磅发布国产1Xnm工艺DDR4内存 实现100%自主可控
英特尔酷睿Ultra 300系列Panther Lake处理器深度解析：架构革新与AI性能飞跃
美政府拟禁售TP-Link路由器 中国制造再遭"安全风险"围剿
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
