Datasheet > R0577YC12C

R0577YC12C

更新时间： 2023-12-06 20:13:28

品牌	Logo	应用领域
力特 - LITTELFUSE		/
页数	文件大小	规格书
13页	4562K
描述
Littelfuse是分布式门极技术领域公认的全球领先公司。这些器件的阻断电压最高可达4.5kV，平均电流超过5kA，额定tq最低为10μs。独特的分布式门极设计和寿命控制功能使这些器件既具有

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

R0577YC12C 数据手册

Distributed Gate Thyristor R0577YS12x

The total dissipation is now given by:

W =W_(original)+ E × f

(TOT)

12.2 Determination without Measurement

In circumstances where it is not possible to measure voltage and current conditions, or for design

purposes, the additional losses E in joules may be estimated as follows.

Let E be the value of energy per reverse cycle in joules (curves in Figure 9).

Let f be the operating frequency in Hz

T_SINK

= T_SINK

)

(

E × R_th× f

)

(

new

)

(

original

Where T_{SINK (new)}is the required maximum heat sink temperature and

T_{SINK (original)}is the heat sink temperature given with the frequency ratings.

A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage

to a peak value (V_rm) of 67% of the maximum grade. If a different grade is being used or V_rmis other than

67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value

obtained from the curves.

NOTE 1- Reverse Recovery Loss by Measurement

This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring

the charge care must be taken to ensure that:

(a) a.c. coupled devices such as current transformers are not affected by prior passage of high

amplitude forward current.

(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope

to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal

damped snubber, connected across diode anode to cathode. The formula used for the calculation

of this snubber is shown below:

V_r

C_S× ^di

R²= 4×

Where: V_r= Commutating source voltage

C_S= Snubber capacitance

= Snubber resistance

13.0 Gate Drive

The recommended pulse gate drive is 30V, 15W with a short-circuit current rise time of not more than

0.5µs. This gate drive must be applied when using the full di/dt capability of the device.

The duration of pulse may need to be configured with respect to the application but should be no shorter

than 20µs, otherwise an increase in pulse current could be needed to supply the resulting increase in

charge to trigger.

Data Sheet. Type R0577YC12x Issue 2

Page 5 of 12

June, 2019

1 2 3 456 7 8...13

下载PDF

与R0577YC12C相关器件

型号	品牌	描述	获取价格	数据表
R0577YS10D	LITTELFUSE	Silicon Controlled Rectifier, 1169A I(T)RMS, 712000mA I(T), 1000V V(DRM), 1000V V(RRM), 1	获取价格
R0577YS10E	LITTELFUSE	Silicon Controlled Rectifier, 1169A I(T)RMS, 712000mA I(T), 1000V V(DRM), 1000V V(RRM), 1	获取价格
R0577YS12D	LITTELFUSE	Silicon Controlled Rectifier, 1169A I(T)RMS, 712000mA I(T), 1200V V(DRM), 1200V V(RRM), 1	获取价格
R0577YS12E	LITTELFUSE	Silicon Controlled Rectifier, 1169A I(T)RMS, 712000mA I(T), 1200V V(DRM), 1200V V(RRM), 1	获取价格
R058	CELDUC	REED RELAY / DRY REED BISTABLE CONTACT	获取价格
R0580	CELDUC	REED RELAY / DRY REED BISTABLE CONTACT	获取价格