Datasheet > MIM-3337S3F

MIM-3337S3F

更新时间： 2024-02-21 11:28:09

品牌	Logo	应用领域
东贝光电 - UOT		/
页数	文件大小	规格书
6页	236K
描述
INFRARED RECEIVER MODULE

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

MIM-3337S3F 技术参数

生命周期：	Contact Manufacturer	Reach Compliance Code：	unknown
风险等级：	5.63	安装特点：	THROUGH HOLE MOUNT
最高工作温度：	85 °C	最低工作温度：	-25 °C
子类别：	Photo ICs	最大压摆率：	0.0025 mA
标称供电电压：	3 V	表面贴装：	NO
Base Number Matches：	1

MIM-3337S3F 数据手册

INFRARED RECEIVER MODULE

MIM-3xx7S3F

Reliability

Test item

High temparature

High temp. & high humi.

Low temparature

Temperature cycle

Dropping

Test condition

t=240H

Standard

Note 2.

Note 3.

Ta=+80^oC

Ta=+40^oC 90%RH

Ta= -30^oC

t=240H

-30oC(0.5H) ~ +80oC(0.5H) 20cycle

Test devices shall be dropped 3 times naturally

onto hard wooden board from a 75cm height position.

NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies

the standard under the conditions below against the standerd transmitter.

(1)Measuring place ………Indoor without extreme reflection of light.

(2)Ambient light source… Detecting surface illumination shall be 200±50Lux under ordinary

hite fluorescense lamp of no high frequency lighting.

(3)Standard transmitter … Burst wave indicated in Fig 1. of standard transmitter

shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2.

NOTE 2. (electro-optical charactistics) shall be satisfied after leaving 2 hours in the normal temperature .

NOTE 3. (electro-optical charactistics) shall be satisfied and no conoid deforms

and destructions of appearance .(excepting deforms of terminals)

Inspection standard

1.Among electrical characteristics , total number shall be inspected on items blow.

1-1 front distance between emitter & detector

1-2 Current consumption

1-3 H level output voltage

1-4 L level output voltage

2.Items except above mentioned are not inspected particularly , but shall fully satisfy

CAUTION ( When use and storage of this device )

1.Store and use where there is no force causing transformation or change in quality .

2.Store and use where there is no corrosive gas or sea(salt) breeze .

3.Store and use where there is no extreme humidity .

4.Solder the lead-pin within the condition of ratings. After soldering do not add extra force .

5.Do not wash this device . Wipe the stains of diode side with a soft cloth. You can

use the solvent , ethylalcohol or methylalcohol or isupropylene only .

6.To prevent static electricity damage to the Pre-AMP make sure that the human body

, the soldering iron is connected to ground before using .

7.Put decoupling device between Vcc and GND for reduse the noise from power supply line .

8.The performance of remote-control system depends on environments condition and ability

of periferal parts. Customer should evaluate the performance as total system in those conditions

after system up with components such as commander , micon and this receiver module .

Others

1.This device is not design to endure radiative rays and heavily charged particles .

2.In case where any trouble or questions arise,both parties agress to make full discussion

covering the said problem .

REV: A1

Unity Opto Technology Co., Ltd.

12/09/2003

6/6

1...3 4 56

下载PDF

与MIM-3337S3F相关器件

型号	品牌	描述	获取价格	数据表
MIM-3337S5F	UOT	INFRARED RECEIVER MODULE	获取价格
MIM-3377H2F	UOT	INFRARED RECEIVER MODULE	获取价格
MIM-3377H3F	UOT	INFRARED RECEIVER MODULE	获取价格
MIM-3377H4	UOT	INFRARED RECEIVER MODULE	获取价格
MIM-3377H8	UOT	INFRARED RECEIVER MODULE	获取价格
MIM-3377J2	UOT	INFRARED RECEIVER MODULE	获取价格

产品中心

服务支持

精选活动

关于我们

帮助中心

MIM-3337S3F

MIM-3337S3F 技术参数

MIM-3337S3F 数据手册

与MIM-3337S3F相关器件

与MIM-3337S3F相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

MIM-3337S3F

MIM-3337S3F 技术参数

MIM-3337S3F 数据手册

与MIM-3337S3F相关器件

与MIM-3337S3F相关文章

您还可以找

您在本页遇到什么问题？