Low RF Susceptibility, Mono Audio
Subsystem with DirectDrive Headphone Amplifier
ABSOLUTE MAXIMUM RATINGS
V
V
V
, PVDD to PGND .............................................-0.3V to +5.5V
to PVDD .........................................................-0.3V to +0.3V
to PGND .........................................................-5.5V to +0.3V
Continuous Current In/Out of HPR and HPL.....................140mA
DD
DD
SS
Continuous Input Current V ...........................................100mA
SS
Continuous Input Current (all other pins) ......................... 20mA
Duration of OUT_ Short Circuit to GND or PVDD.......Continuous
Duration of Short Circuit Between OUT+ and OUT- ..Continuous
Duration of HP_ Short Circuit to GND or PVDD..........Continuous
C1N to PGND..............................................(V - 0.3V) to +0.3V
SS
C1P to PGND...........................................-0.3V to (PVDD + 0.3V)
HPL, HPR to V
SS
(Note 1)......-0.3V to the lower of (PVDD - (V + 0.3V)) or +9V
HPL, HPR to PVDD
Continuous Power Dissipation (T = +70°C)
20-Bump WLP, 5 x 4, Multilayer Board
SS
A
(Note 2) .....+0.3V to the higher of (V - (PVDD - 0.3V)) or -9V
(derate 13.0mW/°C above +70°C)..................................1.04W
Junction Temperature......................................................+150°C
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
SS
MAX9875
GND to PGND..................................................................... 0.3V
INA1, INA2, INB1, INB2, BIAS..................................-0.3V to +4V
SDA, SCL...............................................................-0.3V to +5.5V
All Other Pins to GND..............................-0.3V to (PVDD + 0.3V)
Continuous Current In/Out of PVDD, PGND, OUT_........ 800mA
Note 1: HPR and HPL should be limited to no more than 9V above V , or above PVDD + 0.3V, whichever limits first.
SS
Note 2: HPR and HPL should be limited to no more than 9V below PVDD, or below V - 0.3V, whichever limits first.
SS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
= V
= 3.7V, V
= V
= 0V. Single-ended inputs, preamp gain = 0dB, volume controls = 0dB, OSC = 00, SPKEN = 0,
DD
PVDD
GND
PGND
SHDN = 1. Speaker loads (Z
) connected between OUT+ and OUT-. Headphone loads (R ) connected from HPL or HPR to GND.
SPK
HP
SDA and SCL pullup voltage = 3.3V. Z
= ∞, R = ∞. C1 = C2 = C
= 1µF. T = T
to T , unless otherwise noted. Typical
MAX
SPK
HP
BIAS
A
MIN
values are at T = +25°C.) (Note 3)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
5.25
9.0
UNITS
Supply Voltage Range
V
, PVDD Guaranteed by PSRR test
DD
2.7
V
OSC = 00
5.6
5.5
6.6
HP mode,
OUTMODE = 2
OSC = 10
OSC = 00
OSC = 10
OSC = 00
OSC = 10
11.0
16.0
SPK mode,
OUTMODE = 7
Quiescent Current
I
mA
DD
5.7
10.4
9.3
SPK + HP mode,
OUTMODE = 9
I
V
= I
+ I
; SHDN = 0; V
=
SHDN
VDD
PVDD
SDA
Shutdown Current
Turn-On Time
I
10
22
µA
ms
ms
kΩ
SHDN
= logic-high; T = +25°C
A
SCL
OSC = 00
10
10
Time from shutdown to
full operation
t
OSC = 01
OSC = 10
ON
17.5
After forcing BIAS low, time from BIAS
released to I C reset
BIAS Release Time
Input Resistance
t
25
21
80
BR
2
T
T
= +25°C, preamp gain = 0dB or +9dB
11
3
31
8
A
A
R
IN
= +25°C, preamp gain = +20dB
5.5
Preamp = 0dB
Preamp = +9dB
Preamp = +20dB
2.30
Maximum Input Signal Swing
0.820
0.230
V
P-P
2
_______________________________________________________________________________________