5秒后页面跳转
捷配首页

Datasheet > 电信电路 > ATM/SONET/SDH 集成电路> MAX3864
MAX3864 PDF预览

MAX3864

更新时间： 2024-01-26 14:38:42
品牌 Logo 应用领域
美信 - MAXIM 放大器
页数 文件大小 规格书
12页 869K
描述
2.5Gbps, +3V to +5.5V, Wide Dynamic Range Transimpedance Preamplifier

阅读下载

获取价格

MAX3864 技术参数

是否Rohs认证：不符合生命周期：Obsolete
零件包装代码：SOIC包装说明：SOP, SOP8,.25
针数：8Reach Compliance Code：not_compliant
HTS代码：8542.39.00.01风险等级：5.42
Is Samacsys：N应用程序：ATM;SDH;SONET
JESD-30 代码：R-PDSO-G8JESD-609代码：e0
长度：4.9 mm湿度敏感等级：1
功能数量：1端子数量：8
最高工作温度：85 °C最低工作温度：-40 °C
封装主体材料：PLASTIC/EPOXY封装代码：SOP
封装等效代码：SOP8,.25封装形状：RECTANGULAR
封装形式：SMALL OUTLINE峰值回流温度（摄氏度）：240
电源：3.3/5 V认证状态：Not Qualified
座面最大高度：1.75 mm子类别：Other Telecom ICs
最大压摆率：0.063 mA标称供电电压：3.3 V
表面贴装：YES技术：BIPOLAR
电信集成电路类型：ATM/SONET/SDH SUPPORT CIRCUIT温度等级：INDUSTRIAL
端子面层：Tin/Lead (Sn/Pb)端子形式：GULL WING
端子节距：1.27 mm端子位置：DUAL
处于峰值回流温度下的最长时间：NOT SPECIFIED宽度：3.9 mm
Base Number Matches：1

MAX3864 数据手册

 浏览型号MAX3864的Datasheet PDF文件第1页浏览型号MAX3864的Datasheet PDF文件第3页浏览型号MAX3864的Datasheet PDF文件第4页浏览型号MAX3864的Datasheet PDF文件第5页浏览型号MAX3864的Datasheet PDF文件第6页浏览型号MAX3864的Datasheet PDF文件第7页 
2.5Gbps, +3V to +5.5V, Wide Dynamic Range  
Transimpedance Preamplifier  
ABSOLUTE MAXIMUM RATINGS  
Supply Voltage (V  
- GND).................................-0.5V to +6.0V  
Storage Temperature Range.............................-55°C to +150°C  
Operating Junction Temperature ......................-55°C to +150°C  
Processing Temperature (die) .........................................+400°C  
Lead Temperature (soldering, 10s) .................................+300°C  
CC  
IN Current..............................................................-4mA to +4mA  
FILTER Current......................................................-8mA to +8mA  
Voltages at OUT+, OUT-.................(V  
- 1.5V) to (V  
+ 0.5V)  
CC  
CC  
Continuous Power Dissipation (T = +85°C)  
A
8-Pin SO package (derate 6.7mW/°C above +85°C) ..436mW  
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional  
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to  
absolute maximum rating conditions for extended periods may affect device reliability.  
ELECTRICAL CHARACTERISTICS  
(V  
= +3.0V to +5.5V, 100Ω load between OUT+ and OUT-, 0.1µF coupling capacitors on OUT+ and OUT-, T = -40°C to +85°C,  
A
CC  
unless otherwise noted. Typical values are at +3.3V, source capacitance = 0.85pF, and T = +25°C.) (Note 1)  
A
PARAMETER  
Input Bias Voltage  
CONDITIONS  
MIN  
TYP  
0.83  
34  
MAX  
0.99  
63  
UNITS  
0.66  
V
mA  
Ω
Supply Current  
Transimpedance  
Output Impedance  
Differential, measured with 40µAp-p input  
2100  
48  
2750  
50  
3400  
52  
Single ended (per side)  
Ω
Input = 2mAp-p with 100Ω differential output  
termination  
Maximum Differential Output Voltage  
220  
380  
750  
575  
930  
mVp-p  
Filter Resistor  
600  
2
Ω
mAp-p  
mA  
AC Input Overload  
DC Input Overload  
1
Input-Referred RMS Noise  
Input-Referred Noise Density  
Small-Signal Bandwidth  
Low-Frequency Cutoff  
490  
11  
668  
nA  
Bandwidth = 2.0GHz (Note 2)  
pA/√(Hz)  
MHz  
1525  
40  
2000  
30  
-3dB, input ≤ 20µADC  
kHz  
Gain at 40µAp-p is within 5% of the small-  
signal gain  
Transimpedance Linear Range  
µAp-p  
3.13V < V  
< 5.5V (Note 3)  
24  
24  
67  
77  
CC  
Deterministic Jitter  
ps  
3.0V ≤ V  
≤ 3.13V (Note 3)  
CC  
Output referred, f < 2MHz,  
PSRR = -20log(∆V /∆Vcc)  
Power-Supply Rejection Ratio (PSRR)  
50  
dB  
OUT  
Note 1: Source capacitance represents the total capacitance at the IN pin during characterization of noise and bandwidth parame-  
ters. Noise and bandwidth will be affected by the source capacitance. See the Typical Operating Characteristics for more  
information.  
Note 2: Input-referred noise is calculated as (RMS output noise) / (Gain at f = 10MHz). Noise density is (Input-Referred Noise) /  
1/2  
(Bandwidth) . No external filters are used for the noise measurements.  
Note 3: Deterministic jitter is defined as the arithmetic sum of pulse-width distortion and pattern dependent jitter measured with a  
repeating 20-bit pattern of 00111110101100000101 (K28.5). See Typical Operating Characteristics.  
2
_______________________________________________________________________________________  
1234567...12

下载PDF

与MAX3864相关器件

型号 品牌 描述 获取价格 数据表
MAX38640 ADI 微小尺寸、1.8V–5.5V输入、330nA IQ、700mA nanoPower降压型转

获取价格
MAX38640AELT+ MAXIM Switching Regulator,

获取价格
MAX38640AENT+ MAXIM Switching Regulator,

获取价格
MAX38640BENT+ MAXIM Switching Regulator,

获取价格
MAX38641 ADI 微小尺寸、1.8V–5.5V输入、330nA IQ、700mA nanoPower降压型转

获取价格
MAX38641AELT+ MAXIM Switching Regulator,

获取价格

与MAX3864相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证