MAX17075 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
0.01µF 10ꢀ, 10V X5R ceramic
capacitor (0402)
Murata GRM155R61A103K
TDK C1005X5R1A103K
Not installed, transistor (SOT223)
Recommended: -20V, -1.5A pnp
transistor (SOT223)
C13
C18
1
1
Q2
0
Fairchild BCP69
1500pF 10ꢀ, 50V X7R ceramic
capacitor (0603)
Murata GRM188R71H152K
TDK C1608X7R1H152K
R1
R2
1
0
10Ω 5ꢀ resistor (0603)
Not installed, 100Ω 5ꢀ resistor
(0603) recommended
R3, R4, R5, R7
4
1
1
2
1
1
1
1
1
1
100kΩ 1ꢀ resistors (0603)
13.7kΩ 1ꢀ resistor (0603)
187kΩ 1ꢀ resistor (0603)
20kΩ 1ꢀ resistors (0603)
82kΩ 5ꢀ resistor (0603)
8.45kΩ 1ꢀ resistor (0603)
10kΩ 1ꢀ resistor (0603)
10kΩ 5ꢀ resistor (0603)
1kΩ 5ꢀ resistor (0603)
464kΩ 1ꢀ resistor (0603)
C19
C20
0
0
Not installed, capacitor (1206)
Not installed, capacitor (0402)
R6
R8
0.22µF 10ꢀ, 25V X7R ceramic
capacitor (0603)
Murata GRM188R71E224K
TDK C1608X7R1E224K
R9, R16
R10
C21
1
R11
3A, 30V Schottky diode (M-Flat)
Toshiba CMS02
(Top Mark: S2)
R12
D1
1
3
R13
Evluates:MAX1075
R14
220mA, 100V dual diodes (SOT23)
Fairchild MMBD4148SE
(Top Mark: D4)
R15
D2, D3, D4
10kΩ SMT cermet trimmer, 9 to 15
turns
R17
U1
1
1
JU1
1
2
3-pin header
2-pin headers
JU2, JU3
Boost regulator (24 TQFN)
Maxim MAX17075ETG+
3µH, 3A inductor
DC
Sumida CDRH6D28-3R0
L1
1
—
—
3
1
Shunts
PCB: MAX17075 Evaluation Kit+
Not installed, transistor (SOT223)
Recommended: 20V, 1A npn
transistor (SOT223)
Q1
0
Fairchild BCP68
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Fairchild Semiconductor
Murata Electronics North America, Inc.
Sumida Corp.
888-522-5372
770-436-1300
847-545-6700
847-803-6100
949-623-2900
www.fairchildsemi.com
www.murata-northamerica.com
www.sumida.com
TDK Corp.
www.component.tdk.com
www.toshiba.com/taec
Toshiba America Electronic Components, Inc.
Note: Indicate that you are using the MAX17075 when contacting these component suppliers.
Procedure
Quick Start
Required Equipment
Before beginning, the following equipment is needed:
The MAX17075 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
•
•
+4.5V to +5.5V, 5A DC power supply
One voltmeter
1) Verify that a shunt is installed across pins 2-3 of
jumper JU1 (VCOM unbuffered).
2
_______________________________________________________________________________________