5秒后页面跳转
M0437WC080 PDF预览

M0437WC080

更新时间: 2022-02-26 12:43:14
品牌 Logo 应用领域
IXYS /
页数 文件大小 规格书
11页 794K
描述
Soft Recovery Diode

M0437WC080 数据手册

 浏览型号M0437WC080的Datasheet PDF文件第1页浏览型号M0437WC080的Datasheet PDF文件第2页浏览型号M0437WC080的Datasheet PDF文件第3页浏览型号M0437WC080的Datasheet PDF文件第5页浏览型号M0437WC080的Datasheet PDF文件第6页浏览型号M0437WC080的Datasheet PDF文件第7页 
Soft Recovery Diode Types M0437WC080 to M0437WC140  
5.0 Reverse Recovery Loss  
The following procedure is recommended for use where it is necessary to include reverse recovery loss.  
From waveforms of recovery current obtained from a high frequency shunt (see Note 1) and reverse  
voltage present during recovery, an instantaneous reverse recovery loss waveform must be constructed.  
Let the area under this waveform be E joules per pulse. A new sink temperature can then be evaluated  
from:  
TSINK TJ (MAX ) E   
Where k = 0.2314 (°C/W)/s  
k f RthJK  
E = Area under reverse loss waveform per pulse in joules (W.s.)  
f = Rated frequency in Hz at the original sink temperature.  
RthJK = d.c. thermal resistance (°C/W)  
The total dissipation is now given by:  
W W(original) Ef  
(tot)  
NOTE 1 - Reverse Recovery Loss by Measurement  
This device has a low reverse recovered charge and peak reverse recovery current. When measuring the  
charge, care must be taken to ensure that:  
(a) AC coupled devices such as current transformers are not affected by prior passage of high  
amplitude forward current.  
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope  
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal.  
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically  
damped snubber, connected across diode anode to cathode. The formula used for the calculation of this  
snubber is shown below:  
Vr  
di  
CS   
dt  
R2 4  
Where: Vr = Commutating source voltage  
CS = Snubber capacitance  
R = Snubber resistance  
6.0 Snubber Components  
When selecting snubber components, care must be taken not to use excessively large values of snubber  
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to  
device damage due to the large resultant values of snubber discharge current. If required, please consult  
the factory for assistance.  
Data Sheet. Types M0437WC080 to M0437WC140 Issue 3  
Page 4 of 11  
October 2014  

与M0437WC080相关器件

型号 品牌 描述 获取价格 数据表
M0437WC140 IXYS Soft Recovery Diode

获取价格

M0437WC140 LITTELFUSE 我们的软恢复二极管提供多种反向恢复特性,可满足续流和缓冲应用的需求。 这些器件可提供高达6

获取价格

M0451YC160 IXYS Soft Recovery Diode

获取价格

M0451YC200 IXYS Soft Recovery Diode

获取价格

M04N60 STANSON N Channel MOSFET

获取价格

M05 MEDER Magnet

获取价格