LM4952
www.ti.com
SNAS230A –AUGUST 2004–REVISED MAY 2013
Absolute Maximum Ratings(1)(2)(3)
Supply Voltage (pin 6, referenced to GND, pins 4 and 5)
Storage Temperature
18.0V
−65°C to +150°C
−0.3V to VDD + 0.3V
−0.3V to 9.5V
Internally limited
2000V
pins 4, 6, and 7
Input Voltage
pins 1, 2, 3, 8, and 9
Power Dissipation(4)
ESD Susceptibility(5)
ESD Susceptibility(6)
Junction Temperature
200V
150°C
θJC (TS)
4°C/W
Thermal Resistance
θJA (TS)(4)
20°C/W
(1) All voltages are measured with respect to the GND pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which specify specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature,
TA. The maximum allowable power dissipation is PDMAX = (TJMAX − TA) / θJA or the given in Absolute Maximum Ratings, whichever is
lower. For the LM4952 typical application (shown in Figure 2) with VDD = 12V, RL = 4Ω stereo operation the total power dissipation is
3.65W. θJA = 20°C/W for the DDPAK package mounted to 16in2 heatsink surface area.
(5) Human body model, 100pF discharged through a 1.5kΩ resistor.
(6) Machine Model, 220pF–240pF discharged through all pins.
Operating Ratings
Temperature Range
TMIN ≤ TA ≤ TMAX
−40°C ≤ T A ≤ 85°C
9.6V ≤ VDD ≤ 16V
Supply Voltage
Electrical Characteristics VDD = 12V(1)(2)
The following specifications apply for VDD = 12V, AV = 20dB (nominal), RL = 4Ω, and TA = 25°C unless otherwise noted.
Symbol
Parameter
Conditions
LM4952
Units
(Limits)
Typical(3)
Limit(4)(5)
IDD
ISD
RIN
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, IO = 0A, No Load
VSHUTDOWN = GND(6)
VDC VOL = VDD/2
18
55
35
85
mA (max)
µA (max)
kΩ
Amplifier Input Resistance
44
VDC VOL = GND
200
kΩ
VIN
Amplifier Input Signal
VDD/2
Vp-p (max)
VSDIH
Shutdown Voltage Input High
2.0
VDD/2
V (min)
V (max)
VSDIL
TWU
TSD
PO
Shutdown Voltage Input Low
Wake-up Time
0.4
V (max)
ms
CB = 4.7µF
440
170
Thermal Shutdown Temperature
Output Power
°C
f = 1kHz,
THD+N = 1%
THD+N = 10%
3.1
3.8
2.8
W (min)
(1) All voltages are measured with respect to the GND pin, unless otherwise specified.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which specify specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(3) Typicals are measured at 25°C and represent the parametric norm.
(4) Limits are ensured to AOQL (Average Outgoing Quality Level).
(5) Datasheet min/max specification limits are ensured by design, test, or statistical analysis.
(6) Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to GND for
minimum shutdown current.
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM4952