Electrical Characteristics (Continued)
(V+ = 5.0 VDC, (Note 4))
Parameter
Conditions
LM139A
LM239A, LM339A
LM139
Units
Min Typ Max Min Typ Max Min Typ Max
Saturation Voltage
V
IN(−)=1 VDC, VIN(+) = 0,
700
1.0
700
1.0
700 mVDC
ISINK ≤ 4 mA
Output Leakage Current
VIN(+) = 1 VDC, VIN(−) = 0,
VO = 30 VDC, (LM3302,
1.0
36
µADC
VO = 28 VDC
Keep all VIN’s ≥ 0 VDC (or V−,
)
Differential Input Voltage
36
36
VDC
if used), (Note 8)
Electrical Characteristics
(V+ = 5.0 VDC, (Note 4))
Parameter
Conditions
LM239, LM339
LM2901
LM3302
Units
Min Typ Max Min Typ Max Min Typ Max
Input Offset Voltage
Input Offset Current
Input Bias Current
(Note 9)
9.0
150
400
9
15
40
mVDC
nADC
IIN(+)−IIN(−), VCM = 0V
IIN(+) or IIN(−) with Output in
Linear Range, VCM = 0V (Note 5)
V+ = 30 VDC (LM3302, V+ = 28 VDC
(Note 6)
50
200
300
200 500
V+−2.0
400 700
1.0
1000 nADC
V+−2.0 VDC
700 mVDC
Input Common-Mode
Voltage Range
)
V+−2.0
700
1.0
0
0
Saturation Voltage
VIN(−) = 1 VDC, VIN(+) = 0,
ISINK ≤ 4 mA
Output Leakage Current VIN(+) = 1 VDC, VIN(−) = 0,
1.0
28
µADC
VDC
VO = 30 VDC, (LM3302, V = 28 VDC
)
O
Differential Input Voltage Keep all VIN’s ≥ 0 VDC (or V−,
36
36
if used), (Note 8)
Note 1: For operating at high temperatures, the LM339/LM339A, LM2901, LM3302 must be derated based on a 125˚C maximum junction temperature and a
thermal resistance of 95˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM239 and LM139 must be derated
based on a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small
(P ≤100 mW), provided the output transistors are allowed to saturate.
D
+
Note 2: Short circuits from the output to V can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
+
current is approximately 20 mA independent of the magnitude of V .
Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
+
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V voltage level (or to ground for a large overdrive) for the time
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3 V
(at 25˚)C.
DC
Note 4: These specifications are limited to −55˚C ≤ T ≤ +125˚C, for the LM139/LM139A. With the LM239/LM239A, all temperature specifications are limited to
A
−25˚C ≤ T ≤ +85˚C, the LM339/LM339A temperature specifications are limited to 0˚C ≤ T ≤ +70˚C, and the LM2901, LM3302 temperature range is −40˚C ≤ T
A
A
A
≤ +85˚C.
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
+
+
voltage range is V −1.5V at 25˚C, but either or both inputs can go to +30 V
without damage (25V for LM3302), independent of the magnitude of V .
DC
Note 7: The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3 V
(or 0.3 V below the magnitude of the negative power
DC
DC
supply, if used) (at 25˚C).
+
+
Note 9: At output switch point, V .1.4 V , R = 0Ω with V from 5 V to 30 V ; and over the full input common-mode range (0 V to V −1.5 V ), at 25˚C.
O
DC
S
DC
DC
DC
DC
+
For LM3302, V from 5 V
to 28 V
.
DC
DC
Note 10: Refer to RETS139AX for LM139A military specifications and to RETS139X for LM139 military specifications.
www.national.com
4
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
