2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630-851-4722
Fax: 630- 851- 5040
www.conwin.com
Operating Specifications
Table 2.0
Parameter
Minimum
6.40
Nominal
Maximum
156.25
1.0
Units
MHz
ppm
Notes
Notes:
Center Freq (See Table 8) (Fo)
Frequency Calibration – All Models
-
1) Initial calibration @ 25°C.
Specifications at time of shipment
after 48 hours of operation.
-1.0
1
2
3
2) Frequencystabilityvs. changein
temperature. ±[(Fmax-Fmin)/2], where
the Fmax and Fmin values are in ppm.
Frequency Stability vs. Temperature ± ±(Fmaꢀ-Fmin)ꢁ2ꢂ (See Table 8)
Freq. Stability vs. Voltage - All Models
-
-
± 0.20
ppm
3) Frequency stability for a +/- 5%
supply voltage change.
Total Frequency Tolerance – HTꢀꢀꢀA
through HTꢀꢀꢀF
4) Inclusive of calibration, operating
temperature range, supply voltage
change, shock and vibration and
aging (20 years).
-
-
-
-
-
-
-
-
± 4.6
± 6.1
ppm
ppm
ppm
ppm
4
4
4
Total Frequency Tolerance – HTꢀꢀꢀG
Total Frequency Tolerance – HTꢀꢀꢀH
Aging (20 years) – All Models
5) Oscillator output is enabled with no
connection on pin 1. Output is at
high impedance when disabled.
± 20.0
± 3.0
Operating Temperature Range (See Table 8)
Model: HTꢀꢀ5ꢀ- Series
Model: HTꢀꢀ6ꢀ- Series
0
-
-
70
85
°C
°C
-40
Supply Voltage (See Table 7)
Model: HTFLꢀꢀ or HTVLꢀꢀ - Series (Vcc)
Model: HTFHꢀꢀ or HTVHꢀꢀ - Series (Vcc)
3.135
4.75
3.300
5.00
3.465
5.25
Vdc
Vdc
Supply Current (6.4 to 50 MHz) (Icc)
Supply Current (>50 to 156.25MHz) (Icc)
Phase Jitter (BW =12KHz to Foꢁ2)
Phase Jitter (BW =10Hz to Foꢁ2)
Period Jitter
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6
10
25
1
mA
mA
9
-
-
pS RMS
pS RMS
pS RMS
dBcꢁHz
dBcꢁHz
dBcꢁHz
dBcꢁHz
dBcꢁHz
dBcꢁHz
mS
3
-
3
SSB Phase Noise at 1Hz offset
SSB Phase Noise at 10 Hz offset
SSB Phase Noise at 100 Hz offset
SSB Phase Noise at 1 KHz offset
SSB Phase Noise at 10K Hz offset
SSB Phase Noise at 100 KHz offset
Start-Up Time: Oscillator
-50
-80
-110
-135
-150
-150
-
-
-
-
-
-
-
10
1.0
2.0
TDEV @ 1 second
-
nS
TDEV @ 4 seconds
-
nS
Input Characteristics forVCTCXO Models
Table 3.0
Parameter
Minimum
Nominal
Maximum
Units
Vdc
Vdc
ppm
%
Notes
Control Voltage Range (Vcc = 3.3V) (Vc) 0.3
Control Voltage Range (Vcc = 5.0V) (Vc) 0.5
1.65
3.0
4.5
-
2.5
Frequency Tuning
Linearity
± 10
± 1
-
-
-
Slope
Positive
>100K
Input Resistance
-
-
Ohm
Input Characteristics forTCXO Models
Table 4.0
Parameter
Minimum
Nominal
Maximum
-
Units
Vdc
Notes
Bulletin
Tx137
Enable Voltage (High) (Vih)
Disable Voltage (Low) (Vil)
> 70% Vdd
-
-
-
5
5
Page
2 of 4
05
Revision
Date
< 30% Vdd
Vdc
08 January 2008
Specifications subject to change without notice. All dimensions in inches. © Copyright 1998 The Connor-Winfield Corporation