190W Dual Output with PFC Function
HDP-190
Features :
Universal AC input / Full range
Built-in active PFC function, PF 0.94
High efficiency up to 86%
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
1U low profile 36mm
Conformal coated
ZVS technology to reduce power dissipation
LED indicator for power on
3 years warranty
SPECIFICATION
MODEL
HDP-190
OUTPUT NUMBER
DC VOLTAGE
V1
V2
+3.8V
+2.8V
20A
RATED CURRENT
CURRENT RANGE (max.)
RATED POWER
33A
0 ~ 40A
181.4W (typ.)
0 ~ 22A
192W (max.)
192W continue. V1 total power output shall not exceed 160W (max. 40A) ; V2 total power output shall not exceed 66W (max. 22A)
(The V1 & V2 combine total power output shall not exceed 192W)
OUTPUT POWER (max.)
OUTPUT
RIPPLE & NOISE (max.) Note.2 100mVp-p
VOLTAGE ADJ. RANGE Note.6
100mVp-p
2.5 ~ 3V
2.0%
3.6 ~ 4V
VOLTAGE TOLERANCE Note.3 2.0%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
0.5%
0.5%
2.0%
2.0%
1000ms, 50ms/230VAC
2500ms, 50ms/115VAC at full load
16ms/230VAC
16ms/115VAC at full load
127 ~ 370VDC
Note.5 90 ~ 264VAC
47 ~ 63Hz
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
PF 0.94/230VAC
86%
PF 0.98/115VAC at full load
INPUT
2.7A/115VAC
1.1A/230VAC
45A/230VAC
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
30A/115VAC
<2mA / 240VAC
V1+V2: 105 ~ 150% max. output power ; or V2: 125 ~ 170% rated current
OVERLOAD
Protection type: Hiccup mode, recovers automatically after fault condition is removed
V1: 4.37 ~ 5.13V
V2: 3.22 ~ 3.78V
PROTECTION OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
95
5
(TSW1) detect on heatsink of power transistor
OVER TEMPERATURE
Protection type : Shut down o/p voltage, re-power on to recovery
-30 ~ +70 (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
-40 ~ +85 , 10 ~ 95% RH
ENVIRONMENT
0.03%/ (0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 approved
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) class B, EN61000-3-2,-3
SAFETY &
EMC
(Note 4)
EMC IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2, heavy industry level, criteria A
111.3K hrs min. MIL-HDBK-217F (25
)
MTBF
OTHERS
NOTE
DIMENSION
PACKING
215*115*36mm (L*W*H)
0.95Kg; 15pcs/15.3Kg/0.7CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Derating may be needed under low input voltages. Please check the derating curve for more details.
6. Output voltage between V1 and V2 should be higher than 0.8V(V1-V2 0.8V).
File Name:HDP-190-SPEC 2011-12-28