5秒后页面跳转
捷配首页

Datasheet > GL6UR11T
GL6UR11T PDF预览

GL6UR11T

更新时间： 2024-01-03 02:47:51
品牌 Logo 应用领域
夏普 - SHARP 光电
页数 文件大小 规格书
15页 301K
描述
Single Color LED, Super Luminosity Red, Colorless Transparent, T-1 3/4, 5mm,

阅读下载

获取价格

GL6UR11T 技术参数

是否Rohs认证： 不符合生命周期：Obsolete
Reach Compliance Code：unknown风险等级：5.92
颜色：SUPER LUMINOSITY RED配置：SINGLE
最大正向电流：0.03 AJESD-609代码：e0
透镜类型：COLORLESS TRANSPARENT标称发光强度：300.0 mcd
安装特点：RADIAL MOUNT功能数量：1
端子数量：2最高工作温度：85 °C
最低工作温度：-25 °C光电设备类型：SINGLE COLOR LED
总高度：7.8 mm包装方法：BULK
峰值波长：660 nm形状：ROUND
尺寸：5 mm表面贴装：NO
T代码：T-1 3/4端子面层：Tin/Lead (Sn/Pb)
端子节距：2.54 mmBase Number Matches：1

GL6UR11T 数据手册

 浏览型号GL6UR11T的Datasheet PDF文件第2页浏览型号GL6UR11T的Datasheet PDF文件第3页浏览型号GL6UR11T的Datasheet PDF文件第4页浏览型号GL6UR11T的Datasheet PDF文件第5页浏览型号GL6UR11T的Datasheet PDF文件第6页浏览型号GL6UR11T的Datasheet PDF文件第7页 
General Description of Light Emitting Diodes  
(3) Installation using a holder  
I Handling Precautions  
During an LED lamp positioning, in case of using a holder, holder A  
should be designed to be smaller than the inside dimension of lead  
pins. Holder B should be designed to be larger than the outside  
dimension of lead pins.  
This product is sensitive to static electricity and demands a lot of  
attention. Please take all possible measures for static electricity and  
surge solution.  
(Notes)¡Pay attention to the thermal  
I Lead Forming Method  
expansion coefficient of the  
material used for the holder.  
Since the holder expands and  
Avoid forming a lead pin with the lead pin base as a fulcrum: be  
sure to hold a lead pin firmly when forming.  
Lead pins should be formed before soldering.  
Holder  
A
contracts due to preheat and  
soldering heat, mechanical  
B
stress may be applied to the lead  
pins, resulting in disconnection.  
Hold a lead pin firmly when forming  
(4) Installation to the case  
Do not fix part A with adhesives  
A
when fixed to the case as shown in  
the figure.  
A hole of the case should be  
Case  
I Installation  
(1) Installation on a PWB  
When mounting an LED lamp on a PWB, do not apply physical  
stress to the lead pins.  
designed not to be smaller than the  
outside diameter of LED lamp resin.  
I Soldering Conditions  
Solder the lead pins under the following conditions. (1.6mm or  
more from the resin package)  
(Notes)¡The lead pin pitch should match the PWB pin-hole pitch:  
do not broaden out or narrow down the lead pins.  
¡When positioning an LED lamp, basically employ an  
LED with tie-bar cut or use a spacer.  
Type of Soldering  
1. Manual soldering  
2. Wave soldering  
Conditions  
295˚C ± 5˚C, within 3 seconds  
260˚C ± 5˚C, within 5 seconds  
Preheating 70˚C to 80˚C, within 30 seconds  
Soldering 245˚C ± 5˚C, within 5 seconds  
3. Reflow soldering  
(Notes)¡Avoid dipping resin into soldering bath.  
¡Avoid applying stress to lead pins while they are heated.  
For example, when the LED lamp is moved with the heat  
applied to the lead pins during manual soldering or solder  
repair, disconnection may occur.  
Not acceptable  
PWB  
Acceptable  
I Cleaning  
Conditions described below shall be observed in cleaning.  
(1) Solvent cleaning : Solvent temperature 45˚C or less, for 3 min.  
(2) Ultrasonic cleaning : The affect on the device is different  
depending on the size of the cleaning bath, ultrasonic output, board  
size, and device mounting method. Test the cleaning method under  
actual conditions and check the abnormalities before actual use.  
(3) Recommended solvents are shown below.  
(2) When an LED lamp is mounted directly on a PWB  
If the bottom face of an LED lamp is mounted directly on single-  
sided PWB (1.6mm t or more), the base of the lead pins may be  
subjected to have physical stress due to PWB warp, cutting or  
clinching of lead pins. Prior to use, be sure to check that no  
disconnection inside of the resin or  
Melthyl alcohol, Ethyl alcohol, Isopropyl alcohol.  
When other solvents are used, package resin may be penetrated by  
solvents. Please confirm under actual conditions before use.  
damage to resin etc., is found.  
When an LED lamp is mounted on a  
double-sided PWB, the heat during  
soldering affects the resin; therefore,  
keep the LED lamp more than 1.6mm  
afloat above the soldering position.  
1.6A  
Notice  
In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in  
catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.  
Internet address for Electronic Components Group http://sharp-world.com/ecg/  
2
Internet  
1234567...15

下载PDF

与GL6UR11T相关器件

型号 品牌 描述 获取价格 数据表
GL6UR26T SHARP 5.8X4.6mm, Oval Type, Colored/Colorless Transparency, High-luminosity LED Lamps for Outdoo

获取价格
GL6UR27T SHARP Single Color LED, Super Luminosity Red, Colorless Transparent, 5.8mm, 2 PIN

获取价格
GL6UR31 SHARP ┆5mm(T-1 3/4), Cylinder Type(Flangeless), Col

获取价格
GL6UR3T SHARP Single Color LED, Super Luminosity Red, Colorless Transparent, T-1 3/4, 5mm,

获取价格
GL6ZG27 SHARP Single Color LED, Green, Colorless Transparent, 5.8mm, 2 PIN

获取价格
GL6ZJ27 SHARP DEVICE SPECIFICATION FOR Light Emitting Diode

获取价格

与GL6UR11T相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证