GBPC6005 THRU GBPC610
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes
Case Style GBPC
FEATURES
♦ Plastic package has carries Underwriters Laboratory
0.630 (16.00)
0.590 (14.98)
Flammability Classification 94V-0
0.445 (11.30)
0.405 (10.29)
♦ This series is UL listed under recognized under Component
HOLE FOR
#6 SCREW
0.158 (4.01)
Index, file number E54214
AC
♦ Glass passivated chip junctions
♦ High case dielectric strength of 1500 V
0.142 (3.61)
DIA.
RMS
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
♦ Typical I less than 0.5µA
R
♦ High forward surge current capability
♦ Ideal for printed circuit boards
AC
0.094 (2.4) x 45 degrees
0.128 (3.25)
♦ High temperature soldering guaranteed:
0.048 (1.22)
0.040 (1.02) TYP.
260°C/10 seconds at 5lbs. (2.3 kg) tension
0.750
(19.05)
MIN.
MECHANICAL DATA
Case: Molded plastic body over passivated junction
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
0.042(1.07)
0.038(0.96)
DIA.
0.200 (5.08)
0.160 (4.06)
Mounting Position: Any
(NOTE 1)
Polarity shown on side of case: Positive lead by beveled corner
Mounting Torque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
GBPC
6005
GBPC
601
GBPC
602
GBPC
604
GBPC
606
GBPC
608
GBPC
610 UNITS
SYMBOLS
VRRM
Maximum repetitive peak reverse voltage
Maximum RMS bridge input voltage
Maximum DC blocking voltage
50
35
50
100
70
200
140
200
400
280
400
600
420
600
800
560
800
1000 Volts
700 Volts
1000 Volts
VRMS
DC
V
100
Maximum average forward
rectified output current at
TC=50°C (NOTE1, 2)
6.0
3.0
I(AV)
Amps
TA=40°C
(NOTE 3)
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method)
IFSM
I2t
175.0
127.0
1.0
Amps
A2sec
Volts
Rating for fusing (t<8.3ms)
Maximum instantaneous forward voltage drop
per leg at 3.0 Amperes
VF
Maximum DC reverse current at rated
DC blocking voltage per leg
TA=25°C
TA=125°C
5.0
500.0
IR
µA
pF
Typical junction capacitance per leg (NOTE 4)
CJ
186.0
90.0
Typical thermal resistance per leg (NOTE 3)
RΘJA
RΘJC
22.0
7.3
°C/W
(NOTE 2)
Operating junction temperature range
TJ
-55 to +150
-55 to +150
°C
°C
Storage temperature range
TSTG
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 5.5 x 6.0 x 0.11" thick (14 x 15 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1 MHz and applied reverse voltage of 4.0 Volts
4/98