EVDD408, EVDD409, EVDI409, EVDN409 And EVDD414
IXDD408, IXDD409, IXDI409, IXDN409 And IXDD414
Gate Driver IC Evaluation Boards
General Description
There are three test points on the board: Control, Gate and
Drain. These allow the user to easily attach an oscilloscope
probe and the associated ground to the circuit to verify
performance.
The EVDD408/EVDD409/EVDI409/EVDN409/EVDD414
evaluation boards are general-purpose circuit boards
designed to simplify the evaluation of the IXYS IXDD408,
IXDD409, IXDI409, IXDN409 and IXDD414 gate drive ICs, as
well as to provide a building block for power circuit
development. Any of the four gate driver package types (SO-
8, Dip 8, 5pin TO-220 and the 5pin TO-263) may be installed
in the driver (the 5-Pin TO-263 is factory installed). The board
enables the user to drive MOSFETs or IGBTs in the TO-220,
TO-247, TO-264 or SOT-227 packages. The evaluation
board design allows these MOSFETS to be attached to a
heat sink, and in so doing the board assembly can be used
as a ground referenced, low side power switch for both
single-ended and push-pull configurations. The board layout
for the gate driver in the TO-220 and the TO-263 packages
(designator U1B), allows the ground tab to be soldered to
the ground plane for cooling in high-power, high frequency
applications with large MOSFET devices. Circuitry for the Tri-
State function is also included on the evaluation board.
Figure 1 - EVDD408/EVDD409/EVDI409/EVDN409/EVDD414
Evaluation Board
SOT-227 Device Installed For Illustration Purposes Only
Figure 1 is a photograph of the Evaluation Board loaded with
an IXDD408YI TO-263 driver and a SOT-227 MOSFET. The
low level inputs are shown on the left side of the board.
Control is a TTL high true input which controls the on or off
state of the power switch Q1, Q2, or Q3. Enable is a low true
input, which controls the Tri-State output (IXDD408, IXDD409
and IXDD414 devices only). VCC-IN is the low voltage, (8-
25V) power input, (see Figure 3 below). Figure 2 illustrates
the MOSFET mounting of a TO-220, TO-247, or TO-264
device. The MOSFET is mounted on the back side of the
PCB. A large through hole is provided so that the device can
be attached to a heat sink. The SOT-227 (shown in the
photograph) is mounted in a similar manner.
Evaluation PCB
TO-220, TO-247,
TO-264, or SOT-227
Kapton Insulator
Heat Sink
Figure 2 - Evaluation Board Side View Showing Power
Device Installed In A High-Power Configuration
INPUT
CONTROL
GND1
FUNCTION
Control Input - 3V into 1K Ohms
Ground 1
CircuitOperation
ENABLE *
GND2
LOW = True, HIGH = Tri-State Mode
Ground 2
The schematic diagram for the evaluation board is shown in
Figure 4. The control gate is applied to R6 then on the input
pin 2 of the IC. This signal input is followed in time by the
output pins 7 and 6. Pins 1 and 8 are attached to +VCC via a
de-coupling network comprised of R1, C1 and R2, C2. Pins
4 and 5 are attached to the circuit ground plane. This is the
preferred arrangement of the bypassing for the Vcc input
power. The enable pin 3 is attached to the drain of Q4. This
device is used to level translate and provide an invert
function for the Tri-State mode when used with the IXDD408,
IXDD409 and IXDD414 devices. (The IXDI409 and IXDN409
devices do not utilize the enable input.) The drain of Q4 is
also attached to the gate of the MOSFET thru RA and DA. In
the Tri-State mode the turn-off time of the power MOSFET is
determined by the time constant of the input gate
VCC-IN
GND 3
VCC input - 8V to 25V
Ground 3
* Enable function applies to IXDD408, IXDD409 and
IXDD414 devices only
Figure 3 - Input Pin-Out Table
The Evaluation Boards are supplied with either IXDD408YI,
IXDD409YI, IXDI409YI, IXDN409YI or IXDD414YI 5-Pin TO-
263 devices installed, depending upon the evaluation baord
part number ordered. To use the evaluation board with a
different package type, the installed device must be re-
moved, and the new device installed in the appropriate
location.
capacitance Ciss and the value of the resistor RA. See the
IXDD408 and IXDD414 data sheets for additional
information on this mode of operation.
Ordering Information
Part Number Installed Device
The U1 output is available at pins 7 and 6. These are
attached to the MOSFET via the two one-Ohm resistors R4
and R5. The values of these resistors may be changed to
optimize the performance of the specific device being driven.
EVDD408
EVDD409
EVDI409
EVDN409
EVDD414
IXDD408YI 5-Pin TO-263, 8A With Enable
IXDD409YI 5-Pin TO-263, 9A With Enable
IXDI409YI 5-Pin TO-263, 9A Inverting
IXDN409YI 5-Pin TO-263, 9A Non-Inverting
IXDD414YI 5-Pin TO-263, 14A With Enable
Copyright © IXYS CORPORATION 2001, 2002
First Release
5秒后页面跳转
SI2301 N沟道MOSFET：资料手册参数分析
ADC0809逐次逼近寄存器型模数转换器：资料手册参数分析
AD9361捷变收发器：全面参数解析与关键特性概览
IRF3205功率MOSFET：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
