DRV8212
SLVSFY9B – JUNE 2021 – REVISED AUGUST 2021
DRV8212 11-V H-Bridge Motor Driver with PWM, PH/EN, and Half-Bridge Control
Interfaces and Low-Power Sleep Mode
1 Features
3 Description
•
N-channel H-bridge motor driver
The DRV8212 is an integrated motor driver with
four N-channel power FETs, charge pump regulator,
and protection circuitry. The tripler charge pump
architecture allows the device to operate down to 1.65
V to accommodate 1.8-V supply rails and low-battery
conditions. The charge pump integrates all capacitors
to reduce the overall solution size of the motor driver
on a PCB and allows for 100% duty cycle operation.
– MOSFET on-resistance: HS + LS 280 mΩ
– Drives one bidirectional brushed DC motor
– Two unidirectional brushed DC motors
– One single- or dual-coil latching relay
– Push-pull and bistable solenoids
– Other resistive, inductive, or LED loads
1.65-V to 11-V operating supply voltage range
High output current capability:
– Full-bridge: 4-A peak
– Half-bridge: 4-A peak per output
– Parallel half-bridge: 8-A peak
Multiple interfaces for flexibility and reduced GPIO
Standard PWM Interface (IN1/IN2)
Supports 1.8-V, 3.3-V, and 5-V logic inputs
Ultra low-power sleep mode
– <84.5 nA @ VVM = 5 V, VVCC = 3.3 V, TJ = 25°C
– Timed autosleep mode to reduce GPIO
Protection features
– Undervoltage lockout (UVLO)
– Overcurrent protection (OCP)
– Thermal shutdown (TSD)
Family of devices. See Device Comparison for
details.
– DRV8210: 1.65-11 V, 1 Ω, multiple interfaces
– DRV8210P: Sleep pin, PWM interface
– DRV8212: 1.65-11 V, 280 mΩ, multiple
interfaces
– DRV8212P: Sleep pin, PWM interface
– DRV8220: 4.5-18 V, 1 Ω, multiple interfaces
•
•
The DRV8212 supports multiple control interface
modes including: PWM (IN1/IN2), phase/enable (PH/
EN), independent half-bridge, and parallel half-bridge.
Each interface supports a low-power sleep mode to
achieve ultra-low quiescent current draw by shutting
down most of the internal circuitry.
•
•
•
•
The device can supply up to 4-A peak output current.
It operates with a supply voltage from 1.65 V to 5.5 V.
The driver offers robust internal protection features
include supply undervoltage lockout (UVLO), output
overcurrent (OCP), and device overtemperature
(TSD).
•
•
The DRV8212 is part of a family of devices which
come in pin-to-pin scalable RDS(on) and supply voltage
options to support various loads and supply rails with
minimal design changes. See Device Comparison for
information on the devices in this family. View our full
portfolio of brushed motor drivers on ti.com.
Device Information
PART NUMBER (1)
DRV8212DSG
PACKAGE
WSON (8)
SOT563 (6)
BODY SIZE (NOM)
2.00 mm × 2.00 mm
1.20 mm × 1.60 mm
2 Applications
DRV8212DRL
•
•
•
•
•
•
•
•
•
•
•
Brushed DC motor, solenoid, & relay driving
Water, gas, & electricity meters
IP network camera IR cut filter
Video doorbell
Machine vision camera
Electronic smart lock
Electronic and robotic toys
Blood pressure monitors
Infusion pumps
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
1.65 to 5.5 V
VCC
0 to 11 V
VM
DRV821x
MODE
Control Inputs
H-Bridge
Motor Driver
Electric toothbrush
Beauty & grooming
Protecꢀon
Simplified Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.