Euro Series
E U R O O P T I O N S P E C I F I C AT I O N S
OPTIONS
INPUT
Option “i” (inrush current limiting): A thermistor is connected in series with the
input lines which changes its resistance from high to low when it gets hot. It does
not reduce the current surge if the input power is interrupted for a short period of
time not allowing the thermistor to cool down. Thermistors are fitted as standard
to all mains input models except for 1-phase input of models > 2.5kW.
Thermistors are available up to 45A. For higher input current an electronic inrush
current limitation can be offered.
Option “y” (sys-reset): This logic signal is a combination of power fail and DC-ok
as specified for VME systems.
Option “r” (relay): A relay instead of a logic signal is provided for failure
indication.`
PROGRAMMING & MONITORING
Option “ie” electronic inrush current limiting An electronic circuit limits the inrush
current.
PROGRAMMING SERIES 200-5800, 6600
By external signal, 0-10Vdc
By external signal, 4-20mA
By 270° potentiometer
eu1
eu2
eu3
eu4
ei1
ei2
ei3
ei4
iso
Option “sd” (series diode): A series diode protects the module against input
voltage of wrong polarity (additional power losses).
Of output voltage
from 0 to 100%
Option “ad” (anti-parallel diode):To avoid the power losses of a series diode a diode is
provided with opposite polarity in parallel to the input blowing an internal or external
fuse if the module is connected to a supply with wrong polarity.
By 10 turn potentiometer
By external signal, 0-10Vdc
By external signal, 4-20mA
By 270° potentiometer
Of output current
from 0 to 100%
Option “au” (auto-ranging) For standard dual AC input models the range of
115/230Vac is to be selected by connecting the input line to different pins on the
connector. With auto-ranging the unit senses the input voltage and provides
automatically the correct connection.
By 10 turn potentiometer
Isolating amplifier for programming
Option “p” (power fail): A signal (logic or relay) is given if the input voltage (AC or
DC) drops below the specified limit. In AC input units we sense the rectified input
voltage so that a power fail alarm will not be triggered if at light loads mains
power returns before the input capacitors are substantially discharged.
Programming via interface RS232 or IEEE488
MONITORING SERIES 200-5800, 6600
By external signal, 0-10Vdc
mu1
mu2
mi1
mi2
iso
Of output voltage
from 0 to 100%
Option “r” (relay): A relay instead of a logic signal is provided for failure indication.
By external signal, 4-20mA
By external signal, 0-10Vdc
By external signal, 4-20mA
OUTPUT
Of output current
from 0 to 100%
Option “dd” (decoupling diode): For redundant operation the outputs of two or
more units are paralleled behind de-coupling diodes so that an internal fault of
one module does not affect the operation of the others. These diodes cause power
losses.
Isolating amplifier for programming
Programming via interface RS232 or IEEE488
Option “cs” (active current sharing): An additional control circuit provides active
current sharing via an interconnecting wire between converters that operate in
parallel. Active current sharing should be used for multi-output units operating in
parallel.
CHARGER PROGRAMMING (ALL SERIES)
Temperature compensated charging voltage(sensor not included)
Not interchangeable due to fixed
tc
ts1
ts2
ch1
ch2
ch3
resistor values
Temperature sensor
Option “csi” (current sharing interrupt): Option “csi” will effect the removal of the
“cs” signal. Should there be an instance where a unit is not supplying the load,
then the effect of its “cs” signal is removed, and the load voltage is unaffected by
this condition.
Interchangeable, IC controlled
Automatic selection of charging characteristic (float / equalize
charge) with timer
Additionally: Manual selection of charging characteristic
Option “h1” (inhibit): A terminal connected to the negative input line also shuts off the
converter. This can also be used in conjunction with a thermal trip which shuts the unit
down.
Additionally: Boost charge operation (manually activated with
time delayed return to normal operation)
Option “h2” (inhibit): Operation of the unit is inhibited if a voltage signal
(5V/10mA) is applied in reference to the negative line of the (main) output.
Option “rco” (reducing current limiting at over temperature) A circuit reduces the
current limiting level at higher temperature (to be specified).
Option “d” (DC-ok, one output): A logic signal is given if the output voltage (main
output in multi-output systems) is below the specified limit.
Option “m” (DC-ok, all outputs): In multi-output systems a logic signal is provided
if the voltage of any output is below the specified limit.
Option “ac” (AC ok) A logic signal connected to relay contacts is given if the
output voltage of an inverter is below the specified limit.
Doc. No. PBC9 Rev.C 28-4-11
Powering Progress – www.powerbox.com.au
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
