BA3830F (unless otherwise noted, Ta=25℃,VCC=5V,RL=10MΩ, Rφ1=270kΩ, Rφ2=270kΩ)
Parameter
Quiescent current
Reference output level
(LEVEL)
Symbol
IO
Min.
Typ.
3.8
Max.
5.2
Unit
mA
Conditions
-
VIN = -30dBV, VO = 1.5V (0dB)
When f = center frequencies is input
VIN = -14dBV,
When f = center frequencies is input
VIN = -30dBV, VO= 1.5V (0dB)
f = 1kHz
-3
3.2
-3
Vol
Volmax
Vor
0
3
-
3
dB
V
Max. output level (LEVEL)
4.2
0
Reference output level
(REC LEVEL)
Max. output level
(REC LEVEL)
dB
V
Volmax
3.8
4.8
-
VIN = -14dBV, f = 1kHz
Output offset voltage
Center frequency 1
Center frequency 2
Center frequency 3
Center frequency 4
Center frequency 5
Center frequency 6
Input current when Reset
pin is HIGH
Input current when Reset
pin is ON
Input current when Reset
pin is OFF
Voff
f01
f02
f03
f04
f05
f06
-
49
30
63
150
330
1
90
77
mV
Hz
Hz
With no signal
VIN = -30dBV
VIN = -30dBV
VIN = -30dBV
VIN = -30dBV
VIN = -30dBV
VIN = -30dBV
117
257
0.78
2.55
7.8
183
403
1.22
4.03
12.2
Hz
kHz
kHz
kHz
3.3
10
IIN
Vth
Vth
150
-
215
1.4
1.4
280
1.8
-
μA
V
VIN = 5V
1.0
V
*Q is set to 4.5.
◎ Not designed for radiation resistance.
BA3834F (unless otherwise noted, Ta=25℃,VCC=5V,RL=10MΩ,VAIN=-30dBV,SEL=1)
Parameter
Circuit current
Maximum output level
Symbol
ICC
VOM
Min.
-
Typ.
10
4.8
Max.
15
Unit
mA
V
Conditions
VAIN = 0V, A, B, C, SEL=0
VAIN = -14dBV, Measured at each output
AIN = 0V, SEL=0/1,
4.0
-
V
Output offset voltage
VOS
-
30
150
mV
Measured at each output (cycle time : Ts=50ms)
fIN =68Hz, A=0, B=0, C=1
fIN =170Hz, A=0, B=1, C=0
fIN =420Hz, A=0, B=1, C=1
fIN =1kHz, A=1, B=0, C=0
fIN =2.4kHz, A=1, B=0, C=1
fIN =5.9kHz, A=1, B=1, C=0
fIN =14.4kHz, A=1, B=1, C=1
fIN =1kHz
Standard output level 1
Standard output level 2
Standard output level 3
Standard output level 4
Standard output level 5
Standard output level 6
Standard output level 7
Input impedance
V01
V02
V03
V04
V05
V06
V07
RIN
0.65
0.65
0.65
0.65
0.65
0.65
0.65
80
1.35
1.35
1.35
1.35
1.35
1.35
1.35
100
50
1.70
1.70
1.70
1.70
1.70
1.70
1.70
120
-
V
V
V
V
V
V
V
V
dB
V
Common-mode rejection ratio CMRR
Logic input high level
25
2.5
fIN =1kHz, VAIN =VCIN
VIH
5.0
-
Not Applicable in the when item 3 of the
operation notes applies.
Logic input low level
VIL
-
0
0.5
V
Output response time*1
Discharge level
TO
DL
-
-
5
3
10
-
μs
dB
Reset pulse within TR =10μs (Typ.)*2
*1 The time from the rise of A, B, C or SEL until the rise of AOUT (90% of peak). If the output selection time is less than this,
the output value is not guaranteed and the reset pulse is not generated.
*2 Automatically generated intemally based on the output select signal. For the duration that this signal is “H”, a resistor is
connected to the peak hold capacitor, and the output level drops by -3dB (typ.) for one pulse,
*3 The Q of the bandpass filter is 3.5 for f01 to f06, and 2.5 for f07.
◎ Not designed for radiation resistance.
3/16