Datasheet > B39741B4333P810

B39741B4333P810

更新时间： 2024-02-17 14:11:26

品牌	Logo	应用领域
东电化 - TDK		LTE
页数	文件大小	规格书
9页	132K
描述
SAW Components SAW Rx filter

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

B39741B4333P810 技术参数

是否Rohs认证：	符合	生命周期：	Transferred
包装说明：	SMD, 5 PIN	Reach Compliance Code：	unknown
风险等级：	5.58	中心频率或截止频率 (fo/fc)：	740 MHz
滤波器类型：	SAW FILTER	高度：	0.4 mm
输入阻抗：	50 OHM	最大插入损耗：	2.8 dB
长度：	1.4 mm	安装类型：	SURFACE MOUNT
功能数量：	1	最高工作温度：	85 °C
最低工作温度：	-30 °C	输出阻抗：	100 OHM Ω
物理尺寸：	L1.4XB1.1XH0.4 (mm)/L0.055XB0.043XH0.016 (inch)	宽度：	1.1 mm
Base Number Matches：	1

B39741B4333P810 数据手册

SAW Components

SAW Rx filter

Data sheet

B4333

740.0 MHz

ESD protection of SAW filters

SAW filters are Electro Static Discharge sensitive devices. To reduce the probability of damages

caused by ESD, special matching topologies have to be applied.

In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is

expected.

Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore

only the input matching of the SAW filter has to be designed to short circuit or to block the ESD

pulse.

Below three figures show recommended “ESD matching” topologies.

For wideband filters the high-pass ESD matching structure needs to be at least of 3^rdorder to

ensure a proper matching for any impedance value of antenna and SAW filter input. The required

component values have to be determined from case to case.

Cs1

Cs3

Cs1

Cs3

to output

matching

to output

matching

Lp2

Fig. 1 MLC varistor plus ESD matching

Fig. 2 Suppressor diode plus ESD matching

In cases where minor ESD occur, following simplified “ESD matching” topologies can be used

alternatively.

Cs1

Cs3

to output

matching

Lp2

Fig. 3 3^rdorder high-pass structure for basic ESD protection

In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper

length and width. If this configuration is possible depends on the operating frequency and

available pcb space.

Effectiveness of the applied ESD protection has to be checked according to relevant industry

standards or customer specific requirements

For further information, please refer to EPCOS Application report:

“ESD protection for SAW filters”.

This report can be found under www.epcos.com/rke.Click on “Applications Notes”.

Please read cautions and warnings and

important notes at the end of this document.

August 12, 2014

1...4 5 678 9

下载PDF

与B39741B4333P810相关器件

型号	品牌	描述	获取价格	数据表
B39741B4339P810	TDK	SAW Components SAW Rx filter	获取价格
B39741B4407P810	TDK	SAW Components SAW Duplexer	获取价格
B39741B4413P810	TDK	SAW Components SAW Duplexer	获取价格
B39741B4414P810	TDK	Duplexer,	获取价格
B39741B5124U410	EPCOS	SAW RF filter Basestation	获取价格
B39741B5124U410	TDK	SAW Filter, 1 Function(s), 737MHz, 6 Pin(s), Ceramic, ROHS COMPLIANT, CERAMIC, SMD, DCC6C,	获取价格