37.0-40.0 GHz GaAs MMIC
Buffer Amplifier, QFN
January 2011 - Rev 10-Jan-11
B1014-QT
App Note [1] Biasing - It is recommended to bias the amplifier with Vd=4.0V and IdTOTAL=250mA. It is also recommended to use active
biasing to keep the currents constant as the RF power and temperature vary; this gives the most reproducible results. Depending on the
supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational
amplifier, with a low value resistor in series with the drain supply used to sense the current.The gate of the pHEMT is controlled to maintain
correct drain current and thus drain voltage.The typical gate voltage needed to do this is -0.3V.Typically the gate is protected with Silicon
diodes to limit the applied voltage. Also, make sure to sequence the applied voltage to ensure negative gate bias is available before applying
the positive drain supply.
App Note [2] Bias Arrangement -
Each DC pin (Vd and Vg) needs to have DC bypass capacitance (100pF/10nF/1uF) as close to the package as possible.
MTTF
XB1014-QT: Operating Power De-rating Curve
(continuous)
XB1014-QT: MTTF hours vs. Package Base Temperature
Vd1,2,3=4V; Id1=Id2=62.5mA, Id3=125mA
XB1014-QT: Tch (max) vs. Package Base Temperature
Vd1,2,3=4V; Id1=Id2=62.5mA, Id3=125mA
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
200
1.0E+14
1.0E+13
1.0E+12
1.0E+11
1.0E+10
1.0E+09
1.0E+08
1.0E+07
1.0E+06
1.0E+05
1.0E+04
1.0E+03
180
160
140
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
100
110
120
20
30
40
50
60
70
80
90 100 110 120 130 140 150
20
30
40
50
60
70
80
90
100
110
120
Package Base Temp (ºC)
Package Base Temp (ºC)
Package Base Temp (ºC)
Typical Application
IF In
2 GHz
XP1080-QK XB1014-QT
XU1019-QH
Coupler
RF OUT
37.0-39.5 GHz
Mixer
X
Buffer
X2
LO
Mimix Broadband MMIC-based 37.0-40.0 GHz Transmitter Block Diagram
Factory Automation and Identification
Mimix
Designator
Package
Type
Number of
leads offered
W Tape
Width
P1 Component P0 Hole
Reel
Diameter
Units
per Reel
Pitch
Pitch
-QT
QFN (3x3mm)
12mm
16
8mm
4mm
329mm (13in)
2000
Component Orientation:
Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape’s trailing edge.
Note: Tape and Reel packaging is ordered with a -000T suffix. Package is available in 500 unit reels through designated sales channels.
Minimum order quantities should be discussed with your local sales representative.
Page 5 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2011 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.