5秒后页面跳转
B10011-MFPG1 PDF预览

B10011-MFPG1

更新时间: 2022-11-26 10:31:05
品牌 Logo 应用领域
爱特美尔 - ATMEL /
页数 文件大小 规格书
11页 116K
描述
CAN TRANSCEIVER IC

B10011-MFPG1 数据手册

 浏览型号B10011-MFPG1的Datasheet PDF文件第1页浏览型号B10011-MFPG1的Datasheet PDF文件第2页浏览型号B10011-MFPG1的Datasheet PDF文件第4页浏览型号B10011-MFPG1的Datasheet PDF文件第5页浏览型号B10011-MFPG1的Datasheet PDF文件第6页浏览型号B10011-MFPG1的Datasheet PDF文件第7页 
B10011S  
Absolute Maximum Ratings  
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating  
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this  
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.  
Parameters  
Symbol  
VCC  
VDD  
Vin  
Value  
-0.5 to +36  
-0.5 to +5.5  
-0.5 to VDD  
150  
Unit  
V
Supply voltage  
Controller supply voltage  
Input voltage at any input  
Junction temperature  
V
V
Tj  
°C  
°C  
°C  
Storage temperature range  
Soldering temperature (for 10 s maximum)  
Tstg  
-55 to +150  
260  
Tsld  
Operating Conditions  
Parameters  
Symbol  
VCC  
Value  
7 to 32  
Unit  
V
Supply voltage car battery  
Controller supply voltage  
Control input voltage  
Input voltage  
VDD  
4.75 to 5.25  
0 to VDD  
V
Asel, Bsel  
Tx0  
V
0 to VDD  
V
Operating temperature  
Tamb  
-40 to +105  
°C  
Operating Modes  
0 = 0 V, 1 = 5 V  
Asel  
Bsel  
Rx0  
Mode  
H, L drivers disabled, L load disabled, S-, S+ disabled station not in operation, but  
consuming current  
0
0
3.8 V  
1
0
1
0
1
1
From H  
From L  
Single-wire H, L driver, L load, S-, S+ disabled  
Single-wire L, H driver disabled  
From L-H  
Two-wire operation, normal mode  
ER (error signal) is low when normal operation is disturbed by line faults (interruption,  
short to ground or to VCC, H to L short disturbance by high voltage transients). After a  
waiting period due to transient delays, the controller is asked to test if single-wire opera-  
tion is possible by changing the Asel and Bsel state.  
A
sel and Bsel have an internal pull-up resistor. Therefore, the no-connect state is 1, but  
connection to VDD is recommended when not in use.  
3
4749B–AUTO–09/04  

与B10011-MFPG1相关器件

型号 品牌 描述 获取价格 数据表
B10011S ATMEL CAN TRANSCEIVER IC

获取价格

B10011S_05 ATMEL Can Transceiver IC

获取价格

B10011S_07 ATMEL Can Transceiver IC

获取价格

B10011S-G1 ETC LAN Transceiver

获取价格

B10011S-G3 ETC LAN Transceiver

获取价格

B10011S-MFP ATMEL CAN TRANSCEIVER IC

获取价格