PRELIMINARY
V•I Chip Bus Converter Module
Pin/Control Functions
+IN/-IN – DC Voltage Input Ports
The V•I Chip input voltage range should not be exceeded. An internal
under/over voltage lockout-function prevents operation outside of the
normal operating input range. The BCM turns ON within an input
voltage window bounded by the “Input under-voltage turn-on” and
“Input over-voltage turn-off” levels, as specified. The V•I Chip may be
protected against accidental application of a reverse input voltage by
the addition of a rectifier in series with the positive input, or a reverse
rectifier in shunt with the positive input located on the load side of the
input fuse.
4
3
2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
+Out
-Out
+In
TM
RSV
PC
The connection of the V•I Chip to its power source should be
implemented with minimal distribution inductance. If the interconnect
inductance exceeds 100 nH, the input should be bypassed with a RC
damper to retain low source impedance and stable operation. With an
interconnect inductance of 200 nH, the RC damper may be 100 µF in
series with 0.3Ω. A single electrolytic or equivalent low-Q capacitor
may be used in place of the series RC bypass.
V
W
Y
V
W
Y
+Out
-Out
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
-In
Bottom View
PC – Primary Control
The Primary Control port is a multifunction node that provides the
following functions:
Signal
BGA
Enable/Disable – If the PC port is left floating, the BCM output is
enabled. Once this port is pulled lower than 2.4 Vdc with respect
to –In, the output is disabled. This action can be realized by
employing a relay, opto-coupler, or open collector transistor. Refer
to Figures 1-3, 12 and 13 for the typical Enable/Disable
characteristics. This port should not be toggled at a rate higher
than 1 Hz. The PC port should also not be driven by or pulled up to
an external voltage source.
Name
+In
Designation
A1-L1, A2-L2
AA1-AL1, AA2-AL2
P1, P2
T1, T2
V1, V2
A3-G3, A4-G4,
U3-AC3, U4-AC4
J3-R3, J4-R4,
AE3-AL3, AE4-AL4
–In
TM
RSV
PC
+Out
–Out
Primary Auxiliary Supply – The PC port can source up to 2.4 mA at
5.0 Vdc. The PC port should never be used to sink current.
Alarm – The BCM contains circuitry that monitors output overload,
input over voltage or under voltage, and internal junction
temperatures. In response to an abnormal condition in any of the
monitored parameters, the PC port will toggle. Refer to Figure 13
for PC alarm characteristics.
Figure 14—BCM BGA configuration
TM and RSV – Reserved for factory use.
+OUT/-OUT – DC Voltage Output Ports
Two sets of contacts are provided for the +Out port. They must be
connected in parallel with low interconnect resistance. Similarly, two
sets of contacts are provided for the –Out port. They must be
connected in parallel with low interconnect resistance. Within the
specified operating range, the average output voltage is defined by the
Level 1 DC behavioral model of Figure 25. The current source capability
of the BCM is rated in the specifications section of this document.
The low output impedance of the BCM reduces or eliminates the need
for limited life aluminum electrolytic or tantalum capacitors at the input
of POL converters.
Total load capacitance at the output of the BCM should not exceed the
specified maximum. Owing to the wide bandwidth and low output
impedance of the BCM, low frequency bypass capacitance and
significant energy storage may be more densely and efficiently provided
by adding capacitance at the input of the BCM.
vicorpower.com
800-735-6200
V•I Chip Bus Converter Module
B048K060T24
Rev. 1.0
Page 7 of 15
5秒后页面跳转
74HC573三态非易失锁存器(Latch)资料手册参数分析
MAX3232 RS-232电平转换器资料手册参数分析
MAX485 RS-485/RS-422收发器资料手册参数分析
74HC245八路双向总线收发器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
