Combined Gyroscope
and 3-Axis Accelerometer
ADXC1501
Data Sheet
FEATURES
GENERAL DESCRIPTION
Combined gyroscope and 3-axis, low g accelerometer
Temperature compensated, high precision bias, and
sensitivity performance
The ADXC1501 is a yaw rate gyroscope and 3-axis accelerometer
combined in a single package. It is designed for electronic
stability control and other high performance applications that
require yaw rate and acceleration signals simultaneously. An
internal temperature sensor compensates offset and sensitivity
performance, providing excellent stability over the −40°C to
+105°C temperature range.
30 mg accelerometer bias stability over temperature
2ꢀ°sec gyroscope null stability over temperature
2.5 mg rms typical accelerometer noise at 35.6 Hz
0.1ꢀ°sec rms typical gyroscope noise at 35.6 Hz
Gyroscope: linear acceleration rejection of 0.03ꢀ°sec°g
Acceleration: 32 g overload performance
SPI digital output with a 16-bit data-word and a 4-bit CRC
Comprehensive electromechanical fail-safe features
6 kHz data update rate
Programmable filter response
<16 mA quiescent current draw
3.3 V or 5 V operation
−40ꢀC to +105ꢀC temperature range
A digital serial port interface (SPI) transmits the yaw rate and
acceleration data to a host microcontroller. A 4-bit cyclical
redundancy check (CRC) provides fault coverage for the
transmitted SPI data, and internal fault detection routines
ensure the integrity of all reported yaw rates and acceleration
data. A fully integrated electromechanical continuous self test
(CST) routine provides run-time diagnostic capability for
assessing the health of each MEMS element.
An advanced gyroscope sensor design rejects the linear
acceleration effects of shock and vibration, enabling the ADXC1501
to operate in harsh environments. The accelerometer signal
chain is designed to prevent overload conditions from
occurring in these same harsh environments.
16-lead SOIC package for robust EMI performance
Qualified for automotive applications
APPLICATIONS
Electronic stability control
Chassis control
The ADXC1501 is designed to operate at either 3.3 V or 5 V. At
less than 16 mA current consumption, the ADXC1501 can be
used in energy sensitive applications.
FUNCTIONAL BLOCK DIAGRAM
MISO MOSI SCLK
CS
SYNC TPA
TPB
ACCELERATION
SENSOR
DIE
GYROSCOPE
SENSOR
DIE
SPI INTERFACE
REGISTERS/MEMORY
NVM
TEST/DEBUG
Σ-∆
ADXC1501
MOD
XY
AFE
BAND-
CORIOLIS
AFE
Σ-∆
MOD
Σ-∆
MOD
PASS
FILTER
XY SENSOR
ALU
CLOCK
GENERATION
PHASE-
LOCKED
LOOP
RESONATOR
AFE
TEMP
SENSOR
Σ-∆
MOD
Z-AXIS
GYROSCOPE
TRIM
AND
SELF TEST
SYSTEM
CONTROLLER
Σ-∆
MOD
Z
AFE
Z SENSOR
HIGH VOLTAGE
GENERATION
VOLTAGE REGULATION
CP
VSA
VSD AVDD DVDD AGND DGND VSIO VCM
Figure 1.
For more information about the ADXC1501, contact the Analog Devices, Inc., Customer Interaction Center at
http://www.analog.com/technical_support to connect with a technical support specialist.
Rev. Sp0
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Technical Support
©2017 Analog Devices, Inc. All rights reserved.
www.analog.com