Data Sheet
ADuM6210/ADuM6211/ADuM6212
ELECTRICAL CHARACTERISTICS—5 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
All typical specifications are at TA = 25°C, VDD1 = VDDP = 5 V, VDD2 = 3.3 V, VSEL resistor network: R1 = 10 kΩ, R2 = 16.9 kΩ between VISO
and GNDISO. Minimum/maximum specifications apply over the entire recommended operation range, which is 4.5 V ≤ VDD1, VDDP
≤
5.5 V, 3.0 V ≤ VDD2 ≤ 3.6 V, and −40°C ≤ TA ≤ +105°C, unless otherwise noted. Switching specifications are tested with CL = 15 pF and
CMOS signal levels, unless otherwise noted.
Table 10. DC-to-DC Converter Static Specifications
Parameter
Symbol
Min Typ Max Unit
Test Conditions/Comments
DC-TO-DC CONVERTER SUPPLY
Setpoint
Thermal Coefficient
Line Regulation
Load Regulation
Output Ripple
Output Noise
Switching Frequency
Pulse-Width Modulation Frequency fPWM
Output Supply
Efficiency at IISO (MAX)
IDDP, No VISO Load
IDDP, Full VISO Load
Thermal Shutdown
Shutdown Temperature
Thermal Hysteresis
VISO
3.3
−26
20
1.3
50
130
125
600
V
IISO = 15 mA, R1 = 10 kΩ, R2 = 16.9 kΩ
VISO (TC)
VISO (LINE)
VISO (LOAD)
VISO (RIP)
VISO (NOISE)
fOSC
μV/°C
mV/V
%
mV p-p
mV p-p
MHz
kHz
mA
%
mA
mA
IISO = 15 mA, VDDP = 4.5 V to 5.5 V
IISO = 3 mA to 27 mA
20 MHz bandwidth, CBO = 0.1 µF||10 µF, IISO = 27 mA
CBO = 0.1 µF||10 µF, IISO = 27 mA
3
8
IISO (MAX)
30
3.6 V > VISO > 3 V
IISO = 27 mA
24
3.2
85
IDDP (Q)
IDDP (MAX)
154
10
°C
°C
Table 11. Data Channel Supply Current
1 Mbps—A, B, C Grades
25 Mbps—B, C Grades
100 Mbps—C Grade
Test Conditions/
Unit Comments
Parameter
Symbol Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
SUPPLY CURRENT
ADuM6210
IDD1
IDD2
IDD1
IDD2
IDD1
IDD2
1.1
2.0
2.1
1.7
2.0
1.1
1.6
3.5
2.7
2.3
3.5
1.6
6.2
2.7
4.9
3.9
2.7
6.2
7.0
4.6
6.5
6.2
4.6
7.0
20
4.8
15
11
4.8
20
25
9.0
19
15
9.0
25
mA
mA
mA
mA
mA
mA
CL = 0 pF
CL = 0 pF
CL = 0 pF
CL = 0 pF
CL = 0 pF
CL = 0 pF
ADuM6211
ADuM6212
Table 12. Switching Specifications
A Grade
B Grade
C Grade
Test Conditions/
Comments
Parameter
Symbol Min
Typ Max Min Typ Max Min Typ Max Unit
SWITCHING SPECIFICATIONS
Data Rate
Propagation Delay
Pulse Width Distortion
Pulse Width
Propagation Delay Skew
Channel Matching
Codirectional
Opposing Direction
Jitter
1
50
10
25
35
3
100
26
Mbps Within PWD limit
13
20
tPHL, tPLH
PWD
PW
tPSK
ns
ns
ns
ns
50% input to 50% output
|tPLH − tPHL
Within PWD limit
2.5
|
1000
40
10
38
16
12
Between any two units
tPSKCD
tPSKOD
5
10
3
6
2
5
ns
ns
ns
2
2
1
Rev. 0 | Page 7 of 24