ADuM1300/ADuM1301
Parameter
Symbol
Min
Typ Max Unit
Test Conditions
ADuM130xBRW
Minimum Pulse Width3
Maximum Data Rate4
Propagation Delay5
Pulse-Width Distortion, |tPLH – tPHL
Change vs. Temperature
Propagation Delay Skew6
PW
100 ns
Mbps
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
10
20
tPHL, tPLH
PWD
32
5
50
3
ns
ns
5
|
ps/°C
ns
ns
tPSK
tPSKCD
15
3
Channel-to-Channel Matching,
Codirectional Channels7
Channel-to-Channel Matching,
tPSKOD
6
ns
CL = 15 pF, CMOS signal levels
Opposing-Directional Channels7
ADuM130xCRW
Minimum Pulse Width3
Maximum Data Rate4
PW
8.3
120
27
0.5
3
11.1 ns
Mbps
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
90
18
Propagation Delay5
tPHL, tPLH
PWD
32
2
5
Pulse-Width Distortion, |tPLH – tPHL
Change vs. Temperature
Propagation Delay Skew6
Channel-to-Channel Matching,
Codirectional Channels7
|
ns
ps/°C
ns
ns
tPSK
tPSKCD
10
2
Channel-to-Channel Matching,
tPSKOD
5
ns
CL = 15 pF, CMOS signal levels
Opposing-Directional Channels7
For All Models
Output Disable Propagation Delay
(High/Low-to-High Impedance)
Output Enable Propagation Delay
(High Impedance to High/Low)
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity at
Logic High Output8
tPHZ, tPLH
tPZH, tPZL
6
6
8
8
ns
ns
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
CL = 15 pF, CMOS signal levels
VIx = VDD1/VDD2, VCM = 1000 V,
transient magnitude = 800 V
VIx = 0 V, VCM = 1000 V,
tR/tF
|CMH|
2.5
35
ns
kV/µs
25
25
Common-Mode Transient Immunity at
Logic Low Output8
|CML|
35
kV/µs
transient magnitude = 800 V
Refresh Rate
fr
1.2
0.19
0.05
Mbps
mA/Mbps
mA/Mbps
Input Dynamic Supply Current, per Channel9
IDDI (D)
Output Dynamic Supply Current, per Channel9 IDDO (D)
1 All voltages are relative to their respective ground.
2 The supply current values for all three channels are combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section on
Page 17. See Figure 6 through Figure 8 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 9
through Figure 12 for total IDD1 and IDD2 supply currents as a function of data rate for ADuM1300/ADuM1301 channel configurations.
3 The minimum pulse width is the shortest pulse width at which the specified pulse-width distortion is guaranteed.
4 The maximum data rate is the fastest data rate at which the specified pulse-width distortion is guaranteed.
5 tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
6 tPSK is the magnitude of the worst-case difference in tPHL or tPLH that is measured between units at the same operating temperature, supply voltages, and output load
within the recommended operating conditions.
7 Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
8 CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
9 Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 6 through Figure 8 for information
on per-channel supply current for unloaded and loaded conditions. See the Power Consumption section on Page 17 for guidance on calculating the per-channel
supply current for a given data rate.
Rev. C | Page 4 of 20
5秒后页面跳转
VIPER22A的资料手册解读、引脚参数说明、代换型号推荐
ADS1256的资料手册解读、采集电压范围、读数变化原因分析及实际测量遇到的问题
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
