CN-0121
Circuit Note
CIRCUIT DESCRIPTION
In the setup of Figure 1, connections between boards were
The circuit in Figure 1 was constructed by connecting the
respective evaluation boards for the individual products.
Connections were made with matched cable lengths. The first
of three basic requirements to synchronize multiple AD9910’s is
to provide a co-incident reference clock (REF CLK).
made using matched cables, making it possible to use the
internal default delay values to phase align the SYNC_CLKs.
Figure 3 shows SYNC_CLK phase alignment via the using the
synchronization procedure described.
The last requirement to synchronize multiple DDS devices is a
co-incident IO_UPDATE. The IO_UPDATE must meet setup
and hold times to SYNC_CLK. The IO_UPDATE shown in
Figure 1 is sent synchronously to the SYNC_CLK. The last
requirement now enables the DDS outputs to be controlled.
The setup uses the AD9520 as the REF CLK source for each
AD9910 DDS. The AD9520 runs off an external crystal and the
internal PLL. The AD9520 distributes phase aligned 1 GHz REF
CLKs (PECL outputs) to all four AD9910 evaluation boards. It
also provides a CMOS output clock to the Tektronix DG2020A
data pattern generator for the IO_UPDATE.
Figures 4 and 5 show the DDS outputs in phase alignment.
Having the devices synchronized to one another now enables
predictable phase and/or amplitude adjustment between DDSs.
The next step for synchronization is to align the rising edge of
SYNC_CLK for all four AD9910’s. The SYNC_CLK provides
the reference for a co-incident IO_UPDATE. SYNC_CLK
alignment is accomplished using the internal synchronization
capability of the AD9910. The ADCLK846 distributes phase
aligned SYNC_INs to all four AD9910s. See the AD9910 data
sheet for more details on synchronization capability.
Note, in Figure 5 the system clock was reduced to 100 MHz
operation, and the outputs were unfiltered to display each DDS
raw output. Figure 5 also shows the value of synchronization
with each device outputting the same signal.
Figure 2 shows all four SYNC_CLKs with the AD9910 internal
synchronization circuit disabled. Note that the SYNC_CLKs are
not inherently aligned even when the REF CLKs are phase
aligned.
C3 FREQUENCY
249.54MHz
LOW SIGNAL
AMPLITUDE
1
To phase align the SYNC_CLK rising edges, one AD9910 is
programmed as the master device and the others as slave
devices. The SYNC_OUT of the master device is an LVDS
signal buffered and distributed by the ADCLK846 to all
AD9910 evaluation boards. The SYNC_IN signal (LVDS) must
meet internal setup and hold time requirements of each
device’s system clock. To help support this timing requirement,
the AD9910 features the ability to delay the SYNC_OUT of the
master. For further flexibility, the internal SYNC_IN path of
each device can be independently delayed.
2
3
4
CH1 1.00VΩ CH2 1.00VΩ
CH3 1.00VΩ CH4 1.00VΩ
M2.00ns
CH1
480mV
Figure 3. SYNC_CLK Are Aligned.
C3 FREQUENCY
125.321MHz
C3 FREQUENCY
250.76MHz
1
LOW SIGNAL
AMPLITUDE
1
2
3
2
3
4
4
B
B
B
CH2 200mVΩ
CH4 200mVΩ
M5.00ns CH2
–80V
CH1 200mVΩ
CH3 200mVΩ
W
W
W
B
CH1 1.00VΩ CH2 1.00VΩ
CH3 1.00VΩ CH4 1.00VΩ
M2.00ns
CH2
480mV
W
Figure 4. Filtered DDS Outputs Phase Aligned Using the Setup in Figure 1.
Figure 2. SYNC_CLKs Are Not Aligned.
Rev. A | Page 2 of 3
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
