AD8323
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage +VS
Pins 5, 9, 10, 19, 20, 23, 27 . . . . . . . . . . . . . . . . . . . . . . 6 V
Input Voltages
Pins 25, 26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pins 1, 2, 3, 6, 7 . . . . . . . . . . . . . . . . . . . . . –0.8 V to +5.5 V
Internal Power Dissipation
TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9 W
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature, Soldering 60 seconds . . . . . . . . . . . 300°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
PIN CONFIGURATION
1
2
GND
28
27
26
25
24
23
22
21
20
19
18
17
16
15
DATEN
SDATA
CLK
V
CC
3
V
0.5 V
IN–
GND
4
V
IN+
V
5
GND
CC
6
V
PD
SLEEP
GND
CC
AD8323
TOP VIEW
(Not to Scale)
7
GND
BYP
8
V
9
V
CC
CC
V
10
V
CC
CC
GND 11
GND 12
GND 13
OUT– 14
GND
GND
GND
OUT+
ORDERING GUIDE
Model
Temperature Range
Package Description
JA
Package Option
AD8323ARU
AD8323ARU-REEL
AD8323-EVAL
–40°C to +85°C
–40°C to +85°C
28-Lead TSSOP
28-Lead TSSOP
Evaluation Board
67.7°C/W*
67.7°C/W*
RU-28
RU-28
*Thermal Resistance measured on SEMI standard 4-layer board.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD8323 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Description
1
DATEN
Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A Logic
0-to-1 transition transfers the latched data to the attenuator core (updates the gain) and simulta-
neously inhibits serial data transfer into the register. A 1-to-0 transition inhibits the data latch
(holds the previous gain state) and simultaneously enables the register for serial data load.
2
3
SDATA
CLK
Serial Data Input. This digital input allows for an 8-bit serial (gain) word to be loaded into the
internal register with the MSB (Most Significant Bit) first.
Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit master-
slave register. A Logic 0-to-1 transition latches the data bit and a 1-to-0 transfers the data bit to
the slave. This requires the input serial data word to be valid at or before this clock transition.
4, 8, 11,12,
13, 16, 17, 18,
22, 24, 28
GND
VCC
Common External Ground Reference.
5, 9, 10, 19,
20, 23, 27
Common Positive External Supply Voltage. A 0.1 µF capacitor must decouple each pin.
6
7
PD
Logic “0” powers down the part. Logic “1” powers up the part.
SLEEP
Low Power Sleep Mode. In the Sleep mode, the AD8323’s supply current is reduced to 4 mA. A
Logic “0” powers down the part (High ZOUT State) and a Logic “1” powers up the part.
14
15
21
25
OUT–
OUT+
BYP
Negative Output Signal.
Positive Output Signal.
Internal Bypass. This pin must be externally ac-coupled (0.1 µF cap).
Noninverting Input. DC-biased to approximately VCC/2. For single-ended inverting operation,
use a 0.1 µF decoupling capacitor and a 39.2 Ω resistor between VIN+ and ground.
VIN+
26
VIN–
Inverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 µF capacitor.
–4–
REV. 0
5秒后页面跳转
MAX6675资料手册参数详解、引脚配置说明
LM258引脚图及功能介绍、主要参数分析
CD4052资料手册参数详解、引脚配置说明
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
