AD8099
SPECIFICATIONS WITH +5 V SUPPLY
VS = 5 V @ TA = 25°C, G = +2, RL = 1 kΩ to midsupply, unless otherwise noted. Refer to Figure 60 through Figure 66 for component
values and gain configurations .
Table 2.
Parameter
Conditions
Min
Typ
Max
Unit
DYNAMIC PERFORMANCE
–3 dB Bandwidth
G = +5, VOUT = 0.2 V p-p
G = +5, VOUT = 2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +10, VOUT = 2 V Step
G = +2, VOUT = 2 V Step
G = +2, VOUT = 2 V Step
415
165
440
210
33/23
715
365
18
MHz
MHz
MHz
V/µs
V/µs
ns
Bandwidth for 0.1 dB Flatness (SOIC/CSP)
Slew Rate
630
340
Settling Time to 0.1%
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion (dBc) HD2/HD3
fC = 500 kHz, VOUT = 1 V p-p, G = +10
fC = 10 MHz, VOUT = 1 V p-p, G = +10
f = 100 kHz
–82/–94
–80/–75
0.95
dBc
dBc
Input Voltage Noise
Input Current Noise
Hz
nV/√
pA/√
pA/√
DISABLE
DISABLE
2.6
Hz
Hz
f = 100 kHz,
f = 100 kHz,
pin floating
pin = +VS
5.2
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
0.1
2.5
–6.2
–0.2
0.05
2.4
0.5
mV
µV/°C
µA
DISABLE
DISABLE
–13
–2
1
pin floating
pin = +VS
µA
Input Bias Offset Current
Input Bias Offset Current Drift
Open-Loop Gain
µA
nA/°C
dB
VOUT = 1 V to 4 V
76
88
81
INPUT CHARACTERISTICS
Input Resistance
Differential mode
Common mode
4
10
2
kΩ
MΩ
pF
V
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
1.3 to 3.7
105
VCM = 2 V to 3 V
Output disabled
dB
DISABLE
PIN
DISABLE
<2.4
105
V
Input Voltage
Turn-Off Time
DISABLE
ns
50% of
VIN = 0.5 V, G = +2
DISABLE
to <10% of Final VOUT
,
Turn-On Time
61
ns
50% of
to <10% of Final VOUT
,
VIN = 0.5 V, G = +2
Enable Pin Leakage Current
DISABLE
DISABLE
16
33
21
44
µA
µA
= 5 V
= 0 V
DISABLE
Pin Leakage Current
OUTPUT CHARACTERISTICS
Overdrive Recovery Time (Rise/Fall)
Output Voltage Swing
VIN = 0 to 2.5 V, G = +2
RL = 100 Ω
RL = 1 kΩ
50/70
1.2 to 3.8
1.2 to 3.8
60/80
ns
V
V
mA
dB
1.5 to 3.5
1.2 to 3.8
Short-Circuit Current
Off Isolation
Sinking and Sourcing
DISABLE
–61
f = 1 MHz,
= Low
POWER SUPPLY
Operating Range
Quiescent Current
5
14.5
1.4
89
6
15.4
1.7
V
mA
mA
dB
dB
Quiescent Current (Disabled)
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
DISABLE
= Low
+VS = 4.5 V to 5.5 V, –VS = 0 V (input referred)
+VS =5 V, -VS= –0.5 V to +0.5 V (input referred)
84
84
90
Rev. B | Page 4 of 28