AD8099
SPECIFICATIONS
SPECIFICATIONS WITH 5 V SUPPLY
TA = 25°C, G = +2, RL = 1 kΩ to ground, unless otherwise noted. Refer to Figure 60 through Figure 66 for component values and
gain configurations .
Table 1.
Parameter
Conditions
Min
Typ
Max Unit
DYNAMIC PERFORMANCE
–3 dB Bandwidth
G = +5, VOUT = 0.2 V p-p
G = +5, VOUT = 2 V p-p
G = +2, VOUT = 0.2 V p-p
G = +10, VOUT = 6 V Step
G = +2, VOUT = 2 V Step
G = +2, VOUT = 2 V Step
450
205
510
235
34/25
1350
470
MHz
MHz
MHz
V/µs
V/µs
ns
Bandwidth for 0.1 dB Flatness (SOIC/CSP)
Slew Rate
1120
435
Settling Time to 0.1%
18
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion (dBc) HD2/HD3
fC = 500 kHz, VOUT = 2 V p-p, G = +10
fC = 10 MHz, VOUT = 2 V p-p, G = +10
f = 100 kHz
–102/–111
–84/–92
0.95
dBc
dBc
Input Voltage Noise
Input Current Noise
Hz
nV/√
pA/√
pA/√
DISABLE
DISABLE
2.6
Hz
Hz
f = 100 kHz,
f = 100 kHz,
pin floating
pin = +VS
5.2
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Drift
Input Bias Current
0.1
2.3
–6
0.5
mV
µV/°C
µA
DISABLE
DISABLE
–13
–2
pin floating
pin = +VS
–0.1
3
0.06
85
µA
Input Bias Current Drift
Input Bias Offset Current
Open-Loop Gain
nA/°C
µA
dB
1
82
98
INPUT CHARACTERISTICS
Input Resistance
Differential mode
Common mode
4
10
2
kΩ
MΩ
pF
V
Input Capacitance
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
–3.7 to +3.7
105
VCM
=
2.5 V
dB
DISABLE
PIN
DISABLE
Output disabled
DISABLE
<2.4
105
V
Input Voltage
Turn-Off Time
ns
50% of
VIN = 0.5 V, G = +2
DISABLE
to < 10% of final VOUT
,
Turn-On Time
39
ns
50% of
to < 10% of final VOUT
,
VIN = 0.5 V, G = +2
Enable Pin Leakage Current
DISABLE
DISABLE
17
35
21
44
µA
µA
=+5 V
= –5 V
DISABLE
Pin Leakage Current
OUTPUT CHARACTERISTICS
Output Overdrive Recovery Time (Rise/Fall)
Output Voltage Swing
VIN = -2.5 V to 2.5 V, G =+2
RL = 100 Ω
RL = 1 kΩ
30/50
–3.6 to +3.7
–3.8 to +3.8
131/178
–61
ns
V
V
mA
dB
–3.4 to +3.5
–3.7 to +3.7
Short-Circuit Current
Off Isolation
Sinking and sourcing
DISABLE
f = 1 MHz,
= low
POWER SUPPLY
Operating Range
Quiescent Current
5
15
1.7
91
94
6
16
2
V
mA
mA
dB
dB
Quiescent Current (Disabled)
Positive Power Supply Rejection Ratio
Negative Power Supply Rejection Ratio
DISABLE
= Low
+VS = 4 V to 6 V, –VS = –5 V (input referred)
+VS = 5 V, –VS = –6 V to –4 V (input referred)
85
86
Rev. B | Page 3 of 28