(@ + 25؇C and ؎V = ؎15 V unless otherwise noted)
AD630–SPECIFICATIONS
S
Model
AD630J/A
AD630K/B
Typ
AD630S
Typ
Min
Typ
Max
Min
100
Max
Min
90
Max
Unit
GAIN
Open Loop Gain
90
110
0.1
0.1
2
120
2
110
0.1
0.1
2
dB
%
%
ppm/°C
1, 2 Closed Loop Gain Error
Closed Loop Gain Match
Closed Loop Gain Drift
0.05
0.05
CHANNEL INPUTS
VIN Operational Limit1
Input Offset Voltage
Input Offset Voltage
TMIN to TMAX
Input Bias Current
Input Offset Current
Channel Separation @ 10 kHz
(–VS + 4 V) to (+VS – 1 V)
(–VS + 4 V) to (+VS – 1 V)
(–VS + 4 V) to (+VS – 1 V)
Volts
µV
500
100
500
800
160
1000
µV
nA
nA
dB
100
10
300
50
100
10
300
50
100
10
300
50
100
100
100
COMPARATOR
VIN Operational Limit1
Switching Window
Switching Window
TMIN to TMAX
Input Bias Current
(–VS + 3 V) to (+VS – 1.5 V) (–VS + 3 V) to (+VS – 1.5 V)
(–VS + 3 V) to (+VS – 1.3 V)
Volts
mV
؎1.5
؎1.5
؎1.5
2
؎2.0
؎2.0
؎2.5
mV
nA
ns
100
200
300
100
200
300
100
200
300
Response Time (–5 mV to +5 mV Step)
Channel Status
I
SINK @ VOL = –VS + 0.4 V3
1.6
1.6
1.6
mA
Pull-Up Voltage
(–VS + 33 V)
(–VS + 33 V)
(–VS + 33 V) Volts
DYNAMIC PERFORMANCE
Unity Gain Bandwidth
Slew Rate4
2
45
3
2
45
3
2
45
3
MHz
V/µs
µs
Settling Time to 0.1% (20 V Step)
OPERATING CHARACTERISTICS
Common-Mode Rejection
Power Supply Rejection
Supply Voltage Range
85
90
؎5
105
110
90
90
؎5
110
110
90
90
؎5
110
110
dB
dB
Volts
mA
16.5
5
16.5
5
16.5
Supply Current
4
4
4
5
OUTPUT VOLTAGE, @ RL = 2 kΩ
2
T
MIN to TMAX
؎10
؎10
10
Volts
mA
Output Short Circuit Current
25
25
25
TEMPERATURE RANGES
Rated Performance–N Package
Rated Performance–D Package
0
–25
+70
+85
0
–25
+70
+85
N/A
°C
°C
–55
+125
NOTES
1If one terminal of each differential channel or comparator input is kept within these limits the other terminal may be taken to the positive supply.
2These parameters are guaranteed but not tested for J and K grades. For A, B and S grades they are tested.
3ISINK @ VOL = (–VS + 1) volt is typically 4 mA.
4Pin 12 Open. Slew rate with Pins 12 and 13 shorted is typically 35 V/µs.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
ABSOLUTE MAXIMUM RATINGS
ORDERING GUIDE
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . . 600 mW
Output Short Circuit to Ground . . . . . . . . . . . . . . . . Indefinite
Storage Temperature, Ceramic Package . . . . –65°C to +150°C
Storage Temperature, Plastic Package . . . . . . –55°C to +125°C
Lead Temperature Range (Soldering, 10 sec ) . . . . . . . +300°C
Max Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150°C
Temperature
Ranges
Package
Descriptions Options
Package
Model
AD630JN
AD630KN
AD630AD
AD630BD
AD630SD
0°C to +70°C
0°C to +70°C
Plastic DIP
Plastic DIP
N-20
N-20
–25°C to +85°C Side Brazed DIP D-20
–25°C to +85°C Side Brazed DIP D-20
–55°C to +125°C Side Brazed DIP D-20
THERMAL CHARACTERISTICS
AD630SD/883B –55°C to +125°C Side Brazed DIP D-20
5962-8980701RA –55°C to +125°C Side Brazed DIP D-20
θJC
θJA
AD630SE/883B –55°C to +125°C LCC
5962-89807012A –55°C to +125°C LCC
E-20A
E-20A
20-Pin Plastic DIP (N)
20-Pin Ceramic DIP (D)
20-Pin Leadless Chip Carrier (E)
24°C/W
35°C/W
35°C/W
61°C/W
120°C/W
120°C/W
AD630JCHIPS
0°C to +70°C
Chip
AD630SCHIPS –55°C to +125°C Chip
–2–
REV. C