AD53040
Parameter
Min
Typ
Max
Units
Test Conditions
DYNAMIC PERFORMANCE, DRIVE
(VH and VL) (Continued)
Minimum Pulsewidth
3 V Swing
1.7
2.6
500
ns
4.0 ns Input, 10%/90% Output,
L = 0 V, VH = 3 V
6.0 ns Input, 10%/90% Output,
VL = 0 V, VH = 5 V
V
5 V Swing
ns
Toggle Rate
MHz
VL = –1.8 V, VH = –0.8 V,
VOUT > 600 mV p-p
DYNAMIC PERFORMANCE, INHIBIT
Delay Time, Active to Inhibit
2
2
5
5
ns
ns
Measured at 50%, VH = +2 V,
V
L = –2 V
Delay Time, Inhibit to Active
Measured at 50%, VH = +2 V,
V
V
L = –2 V
H = 0 V, VL = 0 V
I/O Spike
Output Capacitance
<200
5
mV, p-p
pF
Driver Inhibited
POWER SUPPLIES
Total Supply Range
19
V
Positive Supply
Negative Supply
+12
–7
V
V
Positive Supply Current
Negative Supply Current
Total Power Dissipation
Temperature Sensor Gain Factor
75
75
1.43
mA
mA
W
1.15
1.0
µA/K
RLOAD = 10 K, VSOURCE = +12 V
NOTES
Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS1
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Absolute maximum limits apply
individually, not in combination. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Power Supply Voltage
+VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V
–VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –8 V
+VS to –VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +20 V
Inputs
2Output short circuit protection is guaranteed as long as proper heat sinking is
employed to ensure compliance with the operating temperature limits.
3To ensure lead coplanarity (±0.002 inches) and solderability, handling with bare
hands should be avoided and the device should be stored in environments at 24°C
± 5°C (75°F ± 10°F) with relative humidity not to exceed 65%.
DATA, DATA, INH, INH . . . . . . . . . . . . . . . . +5 V, –3 V
DATA to DATA, INH to INH . . . . . . . . . . . . . . . . . . ±3 V
VH, VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . +9 V, –4 V
VH to VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V, 0 V
Outputs
V
OUT Short Circuit Duration . . . . . . . . . . . . . . . .Indefinite2
ORDERING GUIDE
Shipment Method,
VOUT Range in Inhibit Mode
VHDCPL . . . . . Do Not Connect Except for Capacitor to VCC
VLDCPL . . . . . Do Not Connect Except for Capacitor to VEE
THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V, 0 V
Environmental
Operating Temperature (Junction) . . . . . . . . . . . . . .+175°C
Storage Temperature . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec)3 . . . . . . . . . .+260°C
Package
Quantity Per
Package
Model
Description
Shipping Container Option
AD53040KRP 20-Lead Power SOIC Tube, 38 Pieces
RP-20
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD53040 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. B
–3–