A6267
Automotive High Current LED Controller
ELECTRICAL CHARACTERISTICS1 (continued) Valid at TJ = –40°C to 150°C, VIN = 8 to 40 V; unless otherwise noted
Characteristics
Oscillator (continued)
Symbol
Test Conditions
Min.
Typ.
Max.
Unit
OSC Watchdog Period
tOSWD
VCOH
VCOL
Between successive rising edges
IOH = –1 mA
7
VREG – 1
–
–
–
–
–
μs
V
CKOUT Output High Voltage
CKOUT Output Low Voltage
LED Current Sense
VREG
0.4
IOL = 1 mA
V
Input Bias Current LN (BB mode)3
Input Bias Current LP (BB mode)3
Input Bias Current LN (B mode)3
Input Bias Current LP (B mode)3
Differential Input Voltage (Active)
Input Common-Mode Range (BB mode)3
Input Common-Mode Range (B mode)3
Current Error
ILN
ILP
LP = LN = VIN
–
–
6
220
–2
–25
100
–
–
μA
μA
μA
μA
mV
V
LP = LN = VIN
–
ILN
LP = LN = 0 V
–
–
ILP
LP = LN = 0 V
–
–
VIDL
VCMLH
VCMLL
EISL
EN = High, VIDL = VLP – VLN
VLP = VLN
–
–
VIN
0
VIN + 1
VLP = VLN
–
1
5
V
[(10 × ILED × RSL) – 1] × 100
–5
–
%
Switch Current Sense
Input Bias Current
IBIASS
VIDS
IINS
SP = SN = 0 to 2 V
VIDS = VSP – VSN with D = 50%
VIDS = 120 mV
–30
110
–
–
–
180
–
μA
mV
μA
V
Maximum Differential Input Voltage4
Input Source Current
145
120
–
Input Common-Mode Range
Diagnostics and Protection
Fault Blank Timer5
VCMS
VSP = VSN
0
2
tFB
Start-up
–
3
–
ms
V
VREG Undervoltage Turn-Off
VREG Undervoltage Hysteresis
LED String Short Voltage
VREGUV
VREGUVhys
VSCL
Decreasing VREG
4.1
130
430
4.3
150
505
4.5
160
580
mV
mV
Non-Reference LED Short Offset
Voltage
VSCO
160
200
240
mV
Reference LED Short Offset Voltage
LED Open Voltage
VSCOR
VOCL
ILF
430
5
505
5.5
46
170
8
580
6
mV
V
LF Bias Current (BB mode)3
LA Bias Current (BB mode)3
LF Bias Current (B mode)3
LA Bias Current (B mode)3
LED Undercurrent Voltage Difference6
Open Fault Time-Out
LF = LA = VIN + 1.7 V
LF = LA = VIN + 1.7 V
LF = 1.7 V
–
–
μA
μA
μA
μA
mV
ms
ºC
ILA
–
–
ILF
–
–
ILA
LA = 1.7 V
–
34
1
–
VUCL
tOTO
TJF
–
–
fOSC = 350 kHz
–
94
170
15
–
Overtemperature Warning Threshold
Overtemperature Hysteresis
Temperature increasing
Recovery = TJF – TJhys
–
–
TJhys
–
–
ºC
1For input and output current specifications, negative current is defined as coming out of (sourcing) the specified device pin.
2Function is correct but parameters are not guaranteed below the general limit (8 V).
3BB mode = buck-boost (supply-referenced) mode, B mode = boost (ground-referenced) mode.
4Parameters guaranteed by design.
5Fault Blank timer not enabled for open-LED condition.
6Undercurrent when VSENSEL < VIDL– VUCL, where VSENSEL is the voltage across the LED current sense resistor RSL
.
Allegro MicroSystems, Inc.
115 Northeast Cutoff
6
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com