A29001B/A290011B Series
Absolute Maximum Ratings*
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended
periods may affect device reliability.
Ambient Operating Temperature ……... -55°C to +125°C
Storage Temperature ............................. -65°C to +150°C
Ground to VCC……………………….……… -2.0V to 6.5V
Output Voltage (Note 1) …………………… -2.0V to 6.5V
A9,
&
(Note 2)………………. -2.0V to 11.5V
RESET
OE
All other pins (Note 1) ………………………. -2.0V to 6.5V
Output Short Circuit Current (Note 3) ……………. 200mA
Notes:
Operating Ranges
1. Minimum DC voltage on input or I/O pins is -0.5V.
During voltage transitions, inputs may undershoot
VSS to -2.0V for periods of up to 20ns. Maximum DC
voltage on output and I/O pins is VCC +0.5V. During
voltage transitions, outputs may overshoot to VCC
+1.5V for periods up to 20ns.
Commercial Devices
Ambient Temperature (TA) ………………… 0°C to +70°C
Extended Range Devices
Ambient Temperature (TA) ……………… -40°C to +85°C
2. Minimum DC input voltage on A9 pins is -0.5V. During
VCC Supply Voltages
voltage transitions, A9,
and
may
overshoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 and is +11.5V
OE
RESET
VCC for ± 10% devices . . . . . . . . . . . . . . +4.5V to +5.5V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
OE
which may overshoot to 12.5V for periods up to 20ns.
is N/A on A290011B)
(
RESET
3. No more than one output is shorted at a time.
Duration of the short circuit should not be greater than
one second.
Device Bus Operations
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself
does not occupy any addressable memory location. The
register is composed of latches that store the commands,
along with the address and data information needed to
execute the command. The contents of the register serve
as inputs to the internal state machine. The state
machine outputs dictate the function of the device. The
appropriate device bus operations table lists the inputs
and control levels required, and the resulting output. The
following subsections describe each of these operations
in further detail.
Table 1. A29001B/A290011B Device Bus Operations
Operation
A0 – A16
I/O0 - I/O7
WE
CE
OE
RESET
(N/A A290011B)
Read
Write
L
L
H
X
X
H
X
X
H
L
H
AIN
AIN
X
DOUT
DIN
L
H
CMOS Standby
TTL Standby
X
X
H
X
X
High-Z
High-Z
High-Z
High-Z
X
VCC ± 0.5 V
VCC ± 0.5 V
H
L
X
VCC ± 0.5 V
Output Disable
H
L
X
Reset
X
X
X
Temporary Sector Unprotect (Note)
VID
X
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 10.5 ± 1.0V, X = Don't Care, DIN = Data In, DOUT = Data Out, AIN = Address In
Note: 1. See the "Sector Protection/Unprotection" section and Temporary Sector Unprotect for more information.
2. This function is not available on A290011B.
PRELIMINARY (June, 2016, Version 0.0)
4
AMIC Technology, Corp.