Datasheet > A25L16PMF-50F

A25L16PMF-50F

更新时间： 2022-11-29 02:46:31

品牌	Logo	应用领域
联笙电子 - AMICC		闪存
页数	文件大小	规格书
34页	514K
描述
8 Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

A25L16PMF-50F 数据手册

A25L80P

SIGNAL DESCRIPTION

Serial Data Output (Q). This output signal is used to transfer

data serially out of the device. Data is shifted out on the falling

edge of Serial Clock (C).

Serial Data Input (D). This input signal is used to transfer data

serially into the device. It receives instructions, addresses, and

the data to be programmed. Values are latched on the rising

edge of Serial Clock (C).

Serial Clock (C). This input signal provides the timing of the

serial interface. Instructions, addresses, or data present at

Serial Data Input (D) are latched on the rising edge of Serial

Clock (C). Data on Serial Data Output (Q) changes after the

falling edge of Serial Clock (C).

(

) Low enables the device, placing it in the active power

mode.

After Power-up, a falling edge on Chip Select ( ) is required

prior to the start of any instruction.

Hold (

). The Hold (

) signal is used to pause any

HOLD

serial communications with the device without deselecting the

device.

During the Hold condition, the Serial Data Output (Q) is high

impedance, and Serial Data Input (D) and Serial Clock (C) are

Don’t Care. To start the Hold condition, the device must be

selected, with Chip Select ( ) driven Low.

Chip Select ( ). When this input signal is High, the device is

Write Protect ( ). The main purpose of this input signal is to

deselected and Serial Data Output (Q) is at high impedance.

Unless an internal Program, Erase or Write Status Register

cycle is in progress, the device will be in the Standby mode

(this is not the Deep Power-down mode). Driving Chip Select

freeze the size of the area of memory that is protected against

program or erase instructions (as specified by the values in the

BP2, BP1 and BP0 bits of the Status Register).

SPI MODES

edge of Serial Clock (C).

These devices can be driven by a microcontroller with its SPI

peripheral running in either of the two following modes:

– CPOL=0, CPHA=0

– CPOL=1, CPHA=1

For these two modes, input data is latched in on the rising edge

of Serial Clock (C), and output data is available from the falling

The difference between the two modes, as shown in Figure 2,

is the clock polarity when the bus master is in Stand-by mode

and not transferring data:

– C remains at 0 for (CPOL=0, CPHA=0)

– C remains at 1 for (CPOL=1, CPHA=1)

PRELIMINARY (May 2005, Version 0.0)

AMIC Technology Corp.

1 2 345 6 7...34

下载PDF

与A25L16PMF-50F相关器件

型号	品牌	描述	获取价格	数据表
A25L16PMF-50U	AMICC	8 Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface	获取价格
A25L16PMF-50UF	AMICC	8 Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface	获取价格
A25L16PM-U	AMICC	Flash, 16MX1, PDSO8, 0.209 INCH, SOP-8	获取价格
A25L16PM-UF	AMICC	Flash, 16MX1, PDSO8, 0.209 INCH, LEAD FREE, SOP-8	获取价格
A25L16PMW-50	AMICC	8 Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface	获取价格
A25L16PMW-50F	AMICC	8 Mbit, Low Voltage, Serial Flash Memory With 50 MHz SPI Bus Interface	获取价格